PowerBoss Nautilus CE PB45HDSLCE Скачать руководство пользователя страница 92

Страница: 92 / 102

Nautilus Hi-Dump Rider Scrubber/Sweeper #988752UM Rev. * 03/16

Page 92

TROUBLESHOOTING

TROUBLESHOOTING CHART

PROBLEM

POSSIBLE CAUSE(S)

SOLUTION(S)

Engine overheats.

NOTE: If coolant loss has not
occurred, check for malfunction
of the temperature sending unit.

Low coolant level.

Supply coolant.

Fan blade installed incorrect

Reinstall (pusher type fan)

Clogged radiator.

Flush radiator.

Loose fan belt.

Tighten belt.

Defective thermostat.

Replace thermostat.

Nautiilus Hi-Dump® machine
moves slowly
or does not move.

Parking brake is on.

Release brake.

Directional control pedal jammed, damaged, or
not adjusted properly.

Clear jam or adjust linkage.

Tow valve in tow position

Move to drive position

Low hydraulic ﬂ uid level.

Add hydraulic ﬂ uid.

Hydraulic ﬂ uid temperature too high and too
thin caused by excessive load, climbing, high
environment temperatures, worn pump, or
improper ﬂ uid.

Use the proper weight oil for the
operation conditions; check pump.

Hayes coupler failed

Replace

Other problems with the hydraulics system:
pump failure, motor failure, relief valve leaking
or stuck open.

See Hydraulics System
Problems in this section.

Tow Valve improperly set.

Turn to correct position.

Содержание Nautilus CE PB45HDSLCE







































































































Результаты поиска

Содержание Nautilus CE PB45HDSLCE

Отзывы:

Похожие инструкции для Nautilus CE PB45HDSLCE

Бренды по названию

Популярные бренды

PowerBoss Nautilus CE PB45HDSLCE, Руководство пользователя

Результаты поиска

Содержание Nautilus CE PB45HDSLCE

Отзывы:

Похожие инструкции для Nautilus CE PB45HDSLCE

Бренды по названию

Популярные бренды