PowerBoss Nautilus CE PB45HDSLCE Скачать руководство пользователя страница 56

Страница: 56 / 102

Nautilus Hi-Dump Rider Scrubber/Sweeper #988752UM Rev. * 03/16

Page 56

AIR FILTER SERVICE

INDICATOR

AIR FILTER

ELEMENT OUTER

AIR FILTER

ELEMENT INNER

RETAINING

CLAMPS

DUST CAP

Fig. 1: Air Intake System

PREVENTATIVE MAINTENANCE

Air Filter Cleaning

1. Once you have removed the air ﬁ lter elements, empty

the dust cup and clean the interior of the air ﬁ lter
housing.

2. Use an air hose to blow out the air ﬁ lter elements. Air

pressure should be 100 psi (689 kPa) or less.

Air Filter Inspection

1. After you clean the air ﬁ lter elements, check the

elements for holes by passing a light bulb inside it.

Air Filter Installation

1. Wipe out the air cleaner housing with a damp cloth. Be

sure all dirt is removed.

2. Install the cleaned replacement ﬁ lter elements so that the

ﬁ ns are at the far end of the housing. Be careful not to
damage the ﬁ ns.

3. Replace the rubber plug in the dust cup.
4. Replace dust cup, being sure embossed word “top” on

cup is positioned correctly (up).

5. Tighten the retaining clips.
6. Check the condition of intake hoses and clamps. Close

engine top cover and side door.

Содержание Nautilus CE PB45HDSLCE







































































































Результаты поиска

Содержание Nautilus CE PB45HDSLCE

Отзывы:

Похожие инструкции для Nautilus CE PB45HDSLCE

Бренды по названию

Популярные бренды

PowerBoss Nautilus CE PB45HDSLCE, Руководство пользователя

Результаты поиска

Содержание Nautilus CE PB45HDSLCE

Отзывы:

Похожие инструкции для Nautilus CE PB45HDSLCE

Бренды по названию

Популярные бренды