background image

DO’S and DON’TS

4

DO’S

1.    Read and adhere to the instructions both on the machine,  

 

    in the Instruction Guide and Operator Manual.
2.    Ensure pre-operation checks and operations are carried out in   
    the manner described.
3.    Use only on hard, level surfaces able to support the weight of the  
    machine (e.g. concrete floor, tiled floor, hard wood floor).
4.    Ensure operator is fit and does not suffer from fear of heights.
5.    Ensure guardrail gate is closed and latched before elevation.
6.    Ensure work area around the machine is cordoned off from  

 

    pedestrians and other traffic.
7.    Ensure operator is wearing the correct safety equipment.
8.    Ensure the Basket is correctly positioned so as not to come into  
    contact with fixed or moving objects.
9.    Ensure Nano SP is always driven in a safe and sensible manner.   
    Do not drive on a public highway.
10.   Ensure to be careful not to collide with objects when 
    driving Nano SP.
11.   Ensure that the safe working load is evenly distributed 
    in the basket.

  

DON’TS

1.    Never exceed the safe working load (1 person, 200kg).
2.    Never use Nano SP on sloping or uneven ground.
3.    Never use Nano SP as a goods lift or crane.
4.    Never exceed horizontal forces (maximum horizontal 
    force 200N).
5.    Never drive Nano SP near holes in the floor (or edge of concrete  
    slab, manholes, drains etc.)
6.    Never use in the vicinity of live conductors.
7.    Never extend the height or reach of the work platform by using  
    boxes, steps, ladders. 
 8.    Never modify Nano SP in any way without the full approval 
    of the manufacturer.
9.     Avoid contact with fixed objects (walls, buildings etc), and  

 

    moving objects (cranes, vehicles etc).
10.   When used outdoors never attach signs or boards or any  

 

    object which might increase the wind force to the machine 
    and affect stability.
11.   Never exit or enter the work platform other than when it is in the  
    transport position and only via the access gate.
12. Never use the Nano SP in an explosive environment.
13. Never use the machine if you are fatigued.
14. Never use the machine inappropriately or for ‘horseplay.’
15. Never use the machine if under the influence of drugs or alcohol.
16. Never use the machine if suffering from poor health or using    
 

medication which might impair the safe operation of the Nano SP

17. Never use the Nano SP if vision impaired by bright lighting.
18. Never push the Nano SP on sloping surfaces without the use of a 
 

safe method.

19. Never push or pull objects with the platform.
20. Never use on uneven surfaces.
21. Never attach loads such as boards or pipes outside the guard rails  
 

unless authorised to do so by the manufacturer.

Содержание nano SP

























Отзывы: