background image

24 

 

 

 
If the UPS system does not operate correctly, please solve the problem by using the table 

below.   
 

Symptom 

Possible cause 

Remedy 

No indication and alarm even 
though the mains is normal.   

The AC input power is not 
connected well. 

Check  if  input  power  cord 
is  firmly  connected  to  the 
mains.   

The AC input is connected 
to the UPS output. 

Plug  AC  input  power  cord 
to AC input correctly.   

The icon 

and the warning 

code 

  flashing on LCD 

display and alarm is sounding 

every 2 seconds. 

EPO function is activated. 

Set  the  circuit  in  closed 

position  to  disable  EPO 
function, or change polarity 
in UPS Settings. 

The icon 

  and 

 

and the 

warning code 

 

flashing on 

LCD display and alarm is sounding 
every 2 seconds. 

Line and neutral 
conductors of UPS input 
are reversed. 

Rotate mains power socket 
by 180° (Schuko only) and 
then  connect  to  UPS 

system.   
Check building wiring. 

The icon 

  and 

 

and the 

warning code 

 

flashing on 

LCD display. 

The external or internal 
battery is incorrectly or not 

connected. 

Check  if  all  batteries  are 
connected well. 

Fault code is shown as 27 on LCD 

display and alarm is continuously 
sounding. 

Battery voltage is too high 

or the charger is fault. 

Contact your dealer. 

Fault code is shown as 28 on LCD 
display and alarm is continuously 

sounding. 

Battery  voltage  is  too  low 
or the charger is fault. 

Contact your dealer. 

The icon 

  and

 

 

and the 

warning code 

  is flashing on 

LCD display and alarm is sounding 
every second. 

UPS is overloaded. Devices 
connected to the UPS are 
fed directly by the 

electrical network via the 
Bypass. 

Remove excess loads from 
UPS output. 

After repetitive overloads, 
the UPS is locked in the 

Bypass mode. Connected 
devices are fed directly by 
the mains. 

Remove excess loads from 
UPS output first. Then shut 

down  the  UPS  and  restart 
it. 

Fault code is shown as 49 on LCD 

display and alarm is continuously 
sounding. 

UPS is over input current.  Remove excess loads from 

UPS output. 
 

Fault code is shown as 43 and the 
icon 

  is lighting on LCD 

display. Alarm is continuously 

sounding. 

The UPS shut down 
automatically because of 

overload at the UPS 
output. 

Remove excess loads from 
UPS output and restart it. 

5.

 

Troubleshooting 

Содержание VFI1000QS
































Отзывы: