background image

Power-Flo Pumps & Systems • 877-24PUMPS • www.powerflopumps.com

12

LIMITED WARRANTY

PFS411HTCE-2    

 

 

          Submersible Effluent, Sump & Sewage Pumps

Manufacturer warrants, to the immediate purchaser and subsequent initial owner during the warranty period, 
every new pump to be free from defects in material and workmanship under normal use and service, when properly 
used and maintained, for a period of eighteen (18) months from date of manufacture or twelve (12) months from 
date of installation (which ever comes first). Failure due to wear due to excessive abrasives is not covered. The 
initial owner is the purchaser who first uses the pump after its initial installation, or for non-permanent installation, 
the first owner who uses the pump. The date of installation shall be determined by a dated sales receipt noting the 
model and serial number of the pump. The dated sales receipt must accompany the returned pump. Product will be 
repaired, replaced or remanufactured at Manufacturer’s option. No allowance will be made for shipping charges, 
damages, labor or other charges that may occur due to product failure, repair or replacement. This warranty does 
not apply to and there shall be no warranty for any material or product that has been disassembled without prior 
approval of Manufacturer, subjected to misuse, misapplication, neglect, alteration, accident or act of God; that has 
not been installed, operated or maintained in accordance with Manufacturer’s installation instructions; that has 
been exposed to outside substances including but not limited to the following: sand, gravel, cement, mud, tar, 
hydrocarbons, hydrocarbon derivatives (oil, gasoline, solvents, etc.), or other abrasive or corrosive substances, wash 
towels or feminine sanitary products, etc. in all pumping applications. The warranty set out in the paragraph above 
is in lieu of all other warranties expressed or implied; and we do not authorize any representative or other person 
to assume for us any other liability in connection with our products. Contact Manufacturer at:  1-877-24PUMPS or 
www.powerflopumps.com, Attention: Customer Service Department, to obtain any needed repair or replacement 
of part(s) or additional information pertaining to our warranty. 

MANUFACTURER EXPRESSLY DISCLAIMS LIABILITY FOR SPECIAL, CONSEQUENTIAL OR INCIDENTAL
DAMAGES OR BREACH OF EXPRESSED OR IMPLIED WARRANTY; AND ANY IMPLIED WARRANTY OF FITNESS 
FOR A PARTICULAR PURPOSE AND OF MERCHANTABILITY SHALL BE LIMITED TO THE DURATION OF THE 
EXPRESSED WARRANTY.

Some states do not allow limitations on the duration of an implied warranty, so the above limitation may not apply 
to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above 
limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have 
other rights which vary from state to state.

Содержание PFS411HTCE-2 Series













Отзывы: