manualshive.com logo in svg

Potterton Titanium 24, Инструкция по установке и обслуживанию

Поттертон Титаниум 24 - надежный и эффективный котел для вашего дома. Установите его с помощью нашего подробного Руководства по установке и обслуживанию, которое вы можете бесплатно загрузить с manualshive.com. Этот котел обеспечит ваш дом теплом и комфортом на долгие годы.

Поделиться
Скачать
background image

4

Legislation

© Baxi Heating UK Ltd 2014

Codes of Practice - refer to the most recent version

IMPORTANT - Installation, Commissioning, Service & Repair

This appliance must be installed in accordance with the manufacturer’s instructions and

the regulations in force. Read the instructions fully before installing or using the

appliance.

In GB, this must be carried out by a competent person as stated in the Gas Safety

(Installation & Use) Regulations. 

Definition of competence:

A person who works for a Gas Safe registered company

and holding current certificates in the relevant ACS modules, is deemed competent.

All Gas Safe registered engineers carry an ID card with their licence number and a

photograph. You can check your engineer is registered by telephoning 

0800 408 5500 or online at www.gassaferegister.co.uk

In IE, this must be carried out by a competent person as stated in I.S. 813 “Domestic

Gas Installations”.

The addition of anything that may interfere with the normal operation of the appliance

without express written permission from the manufacturer or his agent could invalidate

the appliance warranty. In GB this could also infringe the Gas Safety (Installation and

Use) Regulations.

Warning -

Check the information on the data plate is compatible with local supply

conditions.

This company declare that no substances harmful to health
are contained in the appliance or used during appliance
manufacture.

The appliance is suitable only for installation in GB and IE and
should be installed in accordance with the rules in force, and
only used in a suitably ventilated location.

In GB, the installation must be carried out by a Gas Safe
Registered Installer. It must be carried out in accordance with
the relevant requirements of the:
• Gas Safety (Installation & Use) Regulations.
• The appropriate Building Regulations either The Building 

Regulations, The Building Regulations (Scotland), Building 
Regulations (Northern Ireland).

• The Water Fittings Regulations or Water Byelaws in 

Scotland.

• The Current I.E.E. Wiring Regulations.

Where no specific instructions are given, reference should be
made to the relevant British Standard Code of Practice.

In IE, the installation must be carried out by a competent
Person and installed in accordance with the current edition of
I.S. 813 ‘Domestic Gas Installations’, the current Building
Regulations and reference should be made to the current ETCI
rules for electrical installation.

All systems must be thoroughly flushed and treated with
inhibitor (see section 6.2).

The boiler meets the requirements of Statutory Instrument “ The Boiler (Efficiency)

Regulations 1993 N

o

3083” and is deemed to meet the requirements of Directive

92/42/EEC on the energy efficiency requirements for new hot water boilers fired with

liquid or gaseous fuels:-

Type test for purpose of Regulation 5 certified by: 

Notified Body 0085.

Product/Production certified by:

Notified Body 0086.

For GB/IE only.

In GB the following Codes of Practice apply:
Standard

Scope

BS 6891

Gas Installation.

BS 5546

Installation of hot water supplies for domestic 
purposes.

BS EN 12828

Heating systems in buildings.

BS EN 12831

Heating systems in buildings - Calculation of load.

BS EN 14336

Installation & commissioning of water based 
heating systems.

BS 6798

Installation of gas fired hot water boilers.

BS 5440 Part 1

Flues.

BS 5440 Part 2

Ventilation.

BS 7074

Expansion vessels and ancillary equipment for 
sealed water systems.

BS 7593

Treatment of water in domestic hot water 
central heating systems.

In IE the following Codes of Practice apply:
Standard

Scope

I.S. 813

Domestic Gas Installations.

The following standards give valuable additional information;
BS 5546

Installation of hot water supplies for domestic 
purposes.

BS EN 12828

Heating systems in buildings.

BS EN 12831

Heating systems in buildings - Calculation of load.

BS EN 14336

Installation & commissioning of water based 
heating systems.

BS 7074

Expansion vessels and ancillary equipment for 
sealed water systems.

BS 7593

Treatment of water in domestic hot water 
central heating systems.

Содержание Titanium 24

































































Отзывы:

Нет отзывов

Похожие инструкции для Titanium 24

Laars LMH User Manual preview
LMH
Бренд: Laars Страницы: 9
Laars NEOTHERM NTH Series Installation And Operation Instructions Manual preview
NEOTHERM NTH Series
Бренд: Laars Страницы: 84
Riello INSIEME EVO 25 Installation And Maintenance Manual preview
INSIEME EVO 25
Бренд: Riello Страницы: 44
elco EURON HG 12 Operating Manual preview
EURON HG 12
Бренд: elco Страницы: 52
Bosch 100 EBP Installation And Operating Instructions Manual preview
100 EBP
Бренд: Bosch Страницы: 308
Taco LTA-2 Instruction Sheet preview
LTA-2
Бренд: Taco Страницы: 6
Baxi Solo 3 PFL 30 Installation & Servicing Instructions Manual preview
Solo 3 PFL 30
Бренд: Baxi Страницы: 48
Immergas NIKE Star Instruction Booklet And Warning preview
NIKE Star
Бренд: Immergas Страницы: 112
sylber DEVYL 11 D ie FF Installer And User Manual preview
DEVYL 11 D ie FF
Бренд: sylber Страницы: 92
Ideal Boilers Logic Combi C Manual preview
Logic Combi C
Бренд: Ideal Boilers Страницы: 8
Potterton Cold HE A User Manual preview
Cold HE A
Бренд: Potterton Страницы: 12
Ideal Boilers Classic Combi FF 280 Installation And Servicing preview
Classic Combi FF 280
Бренд: Ideal Boilers Страницы: 56
Potterton Powermax HE 115 Installation And Servicing Instructions preview
Powermax HE 115
Бренд: Potterton Страницы: 68
Britony Britony System 40 Installation And Operation Instructions Manual preview
Britony System 40
Бренд: Britony Страницы: 28
ICI Caldaie SIXEN 1000 Instructions For Installation, Use And Maintenance Manual preview
SIXEN 1000
Бренд: ICI Caldaie Страницы: 40
Ferroli ECOUNIT 1C 200 Manual preview
ECOUNIT 1C 200
Бренд: Ferroli Страницы: 28
Ferroli EASYFIRE 29 Installation, Use And Maintenance Instructions preview
EASYFIRE 29
Бренд: Ferroli Страницы: 208
Wolf CGB-11 Installation Instructions Manual preview
CGB-11
Бренд: Wolf Страницы: 76

Бренды по названию

Популярные бренды

Загрузить еще бренды