Potterton Titanium 24 Скачать руководство пользователя

Страница: 20 / 64

7.0 Site Requirements

7.8

Flue

NOTE:

Due to the nature of the boiler a plume of water

vapour will be discharged from the flue. This should be

taken into account when siting the flue terminal.

1. The following guidelines indicate the general requirements

for siting balanced flue terminals. For GB recommendations are

given in BS 5440 Pt 1. For IE recommendations are given in the

current edition of I.S. 813 “Domestic Gas Installations”.

2. If the terminal discharges onto a pathway or passageway,
check that combustion products will not cause a nuisance and
that the terminal will not obstruct the passageway.

3. If a terminal is less than 2 metres above a balcony, above

ground or above a flat roof to which people have access, then

a suitable terminal guard must be provided.

4. * Reduction to the boundary is possible down to 25mm but

the flue deflector kit (part no. 5111068) must be fitted.

IMPORTANT:

• Under car ports we recommend the use of the plume

displacement kit.

• The terminal position must ensure the safe and

nuisance - free dispersal of combustion products.

D
E

requ

term

guard

Fig. 18

Fig. 17

300 min

Terminal
Assembly

Top View Rear Flue

Property Boundary Line

NOTE:

The distance from a fanned draught appliance terminal

installed parallel to a boundary may not be less than 300mm in
accordance with the diagram below

Opening Window
or Door

150mm
MIN.

IMPORTANT:

If fitting a Plume

Displacement Flue Kit, the air inlet

must be a minimum of 150mm from

any opening windows or doors (see

Section 9.0).

Plume
Displacement Kit

Air Inlet

Fig. 18a

Terminal Position with Minimum Distance (Fig. 18)

(mm)

Directly below an opening, air brick, opening
windows, etc.

300

Above an opening, air brick, opening window etc.

300

Horizontally to an opening, air brick, opening window etc.

300

Below gutters, soil pipes or drain pipes.

25 (75)

Below eaves.

25 (200)

Below balconies or car port roof.

25 (200)

From a vertical drain pipe or soil pipe.

25 (150)

From an internal or external corner.

25 (300)

Above ground, roof or balcony level.

300

From a surface or boundary line facing a terminal.

600

From a terminal facing a terminal (Horizontal flue).

1200

From a terminal facing a terminal (Vertical flue).

600

From an opening in carport (e.g. door, window)
into the dwelling.

1200

Vertically from a terminal on the same wall.

1500

Horizontally from a terminal on the same wall.

300

From adjacent wall to flue (vertical only).

300

From an adjacent opening window (vertical only).

1000

Adjacent to windows or openings on pitched and flat roofs

600

Below windows or openings on pitched roofs

2000

In addition, the terminal should be no nearer than 150 mm to an opening in the

building fabric formed for the purpose of accommodating a built-in element such as
a window frame.

Only

ONE

25mm clearance is allowed per installation. If one of the dimensions

D, E, F, G or H is 25mm then the remainder

MUST

be as shown in brackets, in

accordance with B.S.5440-1.

Содержание Titanium 24

































































Результаты поиска

Содержание Titanium 24

Отзывы:

Похожие инструкции для Titanium 24

Бренды по названию

Популярные бренды

Potterton Titanium 24, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Titanium 24

Отзывы:

Похожие инструкции для Titanium 24

Бренды по названию

Популярные бренды