background image

-  Do not store or use gasoline or other fl ammable vapors and 

liquids in the vicinity of this or any other appliance.

-  WHAT TO DO IF YOU SMELL GAS

-  Do NOT try to light any appliance.
-  Do NOT touch any electrical switch. 
-  Do NOT use any phone in your building.
-  Immediately call your gas supplier from a neighbor’s phone. 

Follow the gas supplier’s instructions.

-  If you cannot reach your gas supplier, call the fi re department.

8U.51.54.02/10.13 

  Changes reserved.

I n s t a l l a t i o n   &   S e r v i c i n g 

Instructions

CAUTION!

Read this manual thoroughly before installing, servicing, putting 
into operation or using this boiler and vent system.

WARNING!

Improper installation, adjustment, alteration, service or 
maintenance can cause property damage, personal injury 
(exposure of hazardous materials)* or loss of life. Refer to the 
user's information manual provided with this boiler. Installation 
and service must be performed by a licensed professional, service 
agency or the gas supplier (who must read and follow the supplied 
instructions before installing, servicing, or removing this boiler).

CAUTION!

The user manual is part of the documentation that is delivered 
to the installation's operator. Go through the information in this 
manual with the owner/operator and make sure that they are 
familair with all necessary operating instructions.

NOTICE!

Installation and service must be performed by a licensed 
professional, service technician or the gas supplier. 

In the Commonwealth of Massachusetts this boiler must be 
installed by a licensed Plumber or Gas Fitter.

High effi ciency condensing gas boiler

Q Premier

QP85N  / QP130N

WARNING!
If you do not follow these instructions exactly, a fi re or explosion 
may result causing property damage, personal injury or loss of life.

These instructions to be retained by user.

Address: 103 International Drive, Peachtree City, GA, 30269

Toll-free: 1-800-621-9419

 • 

Fax: 678-829-1666

 • 

www.rinnai.us

Pictured:  QP130N

Summary of Contents for Q Premier QP130N































































































Reviews: