Potterton Titanium 24 Скачать руководство пользователя

Страница: 14 / 64

6.0 System Details

6.8

Domestic Hot Water Circuit (Fig. 7)

1. All DHW circuits, connections, fittings, etc. should be fully

in accordance with relevant standards and water supply

regulations.

2. Your attention is drawn to:

for GB: Guidance G17 to G24 and recommendation R17 to

R24 of the Water Regulations Guide.

for IE: the current edition of I.S. 813 “Domestic Gas

Installations”.

3. The Water Regulations recommendations for England and

Wales prohibits backflow from appliances into the

wholesome water supply due to thermal expansion.

However this type of instantaneous combination boiler, with

less than 15 litres of stored capacity, does not require any

backflow prevention device as any thermal expansion is

accommodated within the appliance. It is possible in certain

circumstances that other cold water demands (e.g. washing

machines, flushing of W.C.s) may affect the DHW function

of the boiler. In these instances the fitting of a backflow

prevention device and expansion vessel is recommended.

4. Also if there is an existing check valve, loose jumpered

stop cock, water meter or water treatment device already

fitted to the wholesome water supply connected to the

boiler domestic hot water (DHW) inlet supply then a

suitable expansion device may be required.

5. The boiler’s maximum working mains pressure is 8 bar,

therefore all pipework, connections, fittings, etc. should be

suitable for pressures in excess of 8 bar. A pressure reducing

valve must be fitted for pressures in excess of 8 bar. The

manufacturer of any outlet fittings, such as a shower valve,

may require a lower maximum pressure. The pressure

reduction must take account of all fittings connected to the

DHW system.

6.9

Showers

1. If a shower control is supplied from the appliance it

should be of the thermostatic or pressure balanced type.

Thermostatic type shower valves provide the best comfort

and guard against water at too high a temperature. Existing

controls may not be suitable - refer to the shower valve

manufacturer.

6.10

Hard Water Areas

1. If the area of the installation is recognised as a HARD

WATER AREA then a suitable device should be fitted to

treat the mains water supply to the boiler. Contact your

Water Distribution Company for advice on suitable devices.

Boiler

Other Tap
Outlets

Expansion
Vessel*

To Hot
Taps

Check
Valve*

Pressure Reducer
Valve*

Stop Tap

Fig. 7

* See 6.8 for instances when
these items may be required

Содержание Titanium 24

































































Результаты поиска

Содержание Titanium 24

Отзывы:

Похожие инструкции для Titanium 24

Бренды по названию

Популярные бренды

Potterton Titanium 24, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Titanium 24

Отзывы:

Похожие инструкции для Titanium 24

Бренды по названию

Популярные бренды