background image

 

 

 
 
 
 
 

 

FCC Notes: 

This  equipment  generates,  uses,  and  can  radiate  radio  frequency 
energy  and,  if  not  installed  and  used  in  accordance  with  the 
instructions 

manual, 

may 

cause 

interference 

to 

radio 

communications. It has been tested and found to comply with limits 
for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to 
provide  reasonable  protection  against  interference  when  operated  in  a  commercial  environment. 
Operation of this equipment in a residential area is likely to cause interference in which case the 
user at his own expense will be required to take whatever measures to correct the interference. 

CE manufacturer’s Declaration of Conformity 
(EC Council Directive 89/336/EEC of 3 May 1989) 

This product has been designed and manufactured in accordance with the International Standards 
EN50081-1/01.92  and  EN50082-1/01.92  following  the  provisions  of  the  Electro  Magnetic 
Compatibility Directive of the European Communities as of May 1989 

Warranty Limits: 

Warranty  terminates  automatically  when  any  person  other  than  the  authorized  technicians  opens 
the machine. The user should consult his/her dealer for the problem happened. Warranty voids if 
the user does not follow the instructions in application of this merchandise. The manufacturer is by 
no means responsible for any damage or hazard caused by improper application. 

About This Manual: 

Posiflex has made every  effort for the accuracy of the content in this manual. However, Posiflex 
will  assume  no  liability  for  any

 

technical  inaccuracies  or  editorial  or  other  errors  or  omissions 

contained herein, nor for direct, indirect, incidental, consequential or otherwise damages, including 
without limitation loss of data or profits, resulting from the furnishing, performance, or use of this 
material.

 

This  information  is  provided  “as  is”  and  Posiflex  Technology,  Inc.  expressly  disclaims  any 
warranties,  expressed,  implied  or  statutory,  including  without  limitation  implied  warranties  of 
merchantability or fitness for particular purpose, good title and against infringement. 
The information in this manual contains only essential hardware concerns for general user and is 
subject  to  change  without  notice.  Posiflex  reserves  the  right  to  alter  product  designs,  layouts  or 
drivers  without  notification.  The  system  integrator  shall  provide  applicative  notices  and 
arrangement  for  special  options  utilizing  this  product.  The  user  may  find  the  most  up  to  date 
information 

of 

the 

hardware 

from 

web 

sites: 

http://www.posiflex.com 

or 

http://www.posiflex.com.tw or http://www.posiflexusa.com 
All  data  should  be  backed-up  prior  to  the  installation  of  any  drive  unit  or  storage  peripheral. 
Posiflex will not be responsible for any loss of data resulting from the use, disuse or misuse of this 
or any other Posiflex product. 
All  rights  are  strictly  reserved.  No  part  of  this  documentation  may  be  reproduced,  stored  in  a 
retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, 
or otherwise, without prior express written consent from Posiflex Technology, Inc. the publisher of 
this documentation. 

©

 Copyright Posiflex Technology, Inc. 2011

 

All  brand  and  product  names  and  trademarks  are  the  property  of  their  respective  holders.

Aura – 5200E 

  THERMAL PRINTER 

USER’S MANUAL

 

Rev.: B0 

P/N: 

19740900020

 

Содержание Aura-5200E





















Отзывы: