background image

13. 

Slide the guide with the handles onto the slat pins upwards from 

   

the bottom of the blind. Insert the handle pins (1.) carefully into the 

   

upper part of the guides. Check if the elements are installed 

   

correctly. Do not push the blind guides onto the pins which may 

   

damage the guides

.

14. 

Measure the position of the guide axis carefully, then 

   

screw the guides to the ground

.

15. 

Install the guide end caps

.

16. After checking the correctness of the external blind operation, 
   set the roller mechanism in a vertical axis with the winding tape, 
   and then tighten the counter screws (1).

17. 

Insert safety plate extensions into previously installed 

   

wall handles

 

and screw them

.

18. 

Place the extension silencing element onto the lower parts 

   

of the extensions

.

12. 

Slide the guide handle into the rear wall of the guide 

   

and block the handle by tightening the grub screw. 

   

The maximum distance between the handles should 

   

not exceed 800mm

.

5

max. 800mm

1.

11. 

Join the guide with the supplied crank by means of connecting 

   

elements (provided by the PORTOS company) as in Figure 1. 

   

Install the crank clip to the wall with screws (dowels)

.

1.

ZF3000 

EXTERNAL BLIND INSTALLATION

1

Содержание ZF3000 C80















Отзывы: