background image

Emergency situations

:

1. 

It should be noted that in winter during strong frosts, do not leave the blind partially lifted when 

opening the window. The difference in temperatures causes the water vapor to deposit on the 
blind and consequently its subsequent freezing. Therefore, before opening the window, the blind 
slats should be lifted completely up

.

2. 

In winter, slats may be covered with ice and frozen to the ground. An attempt to open a blind in 

such a situation may lead to breaking of the curtain (especially with the electric drive). In the 
period of snowfalls or heavy frosts, before activating the blind, check that there is no ice or snow 
on the window sill or in the guides. If the blind is icy, crush the ice gently or wait for it to melt

.

3. 

During the expected snowfalls or strong frosts it is recommended to turn off the timer control and 

operate the blinds manually, controlling their opening and closing

.

4. 

In the event of possible strong gusts of wind, it is recommended to leave the blinds with the slats 

fully lifted

.

Maintenance

:

The basic rules of the product maintenance consist of cyclical monitoring of the correctness of coiling 
and uncoiling the blinds, precise positioning of the end positions and cleaning of accessible elements of 
the product. The blind should be cleaned with a soft cloth using generally available cleaning agents. The 
use of pressure washers, strong cleaning agents and solvents is forbidden. When cleaning the product, 
it is absolutely not advisable to use sharp tools and cleaning agents that cause scratches. In the case of 
cleaning the product, it is unconditionally necessary to prevent the possibility of water getting into the top 
rail of the product

.

Safety regulations

:

1. 

Do not stay in the blind operation area during lifting and lowering

.

2. 

When using the blind, attention should be paid to the condition of the tape and ladder. Their 

damage may cause the slats to fall automatically and damage to the blind elements

.

3. 

In case of finding any part of the blind damaged or irregularities in its operation, cease its 

operation and call the service. Using a damaged or a defective blind may result in a risk to the 
user's health and life

.

4. 

In the case of replacement of damaged elements, use only original spare parts

.

5. 

In the event of a breakdown, it is forbidden to make any temporary repairs

.

6. 

Any work related to the repair or replacement of damaged parts of the external blind may only be 

performed by a trained person. Self-repair attempts may result in the loss of the warranty

.

7. 

The remote control elements should be stored in places that are difficult to reach for children

.

8. 

Do not use the product with visible signs of damage or wear of the electrical wiring

.

Содержание ZF3000 C80















Отзывы: