Porter-Cable PCCS300, Инструкция по эксплуатации

Страница: 11 / 36

9
English
Speed Selection and Lock‑Off Button
(Fig. A)
The tool features two speed setting ranges (LOW & HIGH) for
greater versatility. The trigger controls variable speed within
these two speed setting ranges.
nOTE:
Do not change speeds when the tool is running.
Always allow the tool to come to a complete stop before
changing speed.
1. To select speed 1 (low speed), slide the speed selector 4
on the side marked "low".
2. To select speed 2 (high speed), slide the speed selector
on the side marked "high".
3. To lock the tool trigger, slide the speed selector to the
center position. When the lock/speed change lever is
in the center position, the tool is locked and the trigger
switch cannot be pulled.
Trigger On/Off Switch (Fig. A)
The tool is turned on and off by pulling and releasing the
variable speed trigger
3
. The farther the trigger is depressed,
the higher the speed of the tool. Release trigger to turn
saw off.
WARNING:
This tool has no provision to lock the
switch in the ON position, and should never be locked
ON by any other means.
Proper Hand Position (Fig. D)
WARNING:
To reduce the risk of serious personal
injury,
ALWAYS
use proper hand position as shown.
WARNING:
To reduce the risk of serious personal
injury,
ALWAYS
hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the hand grip 9 ,
with the other hand on the main handle
8
.
nOTE: For best results, use a 4.0 Ah battery pack.
Installing and Removing the Battery Pack
(Fig. C)
WARNING:
Ensure the tool/appliance is in the off
position before inserting the battery pack.
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
1 into the tool handle, align the
battery pack with the rails inside the tool’s handle and slide
it into the handle until the battery pack is firmly seated in the
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button
2 and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories.
An
accidental start‑up can cause injury.
WARNING: Cut hazard. Blade breakage may occur
if the blade does not extend past the shoe and the
thickness of the workpiece during the cut. Increased risk
of personal injury, as well as damage to the shoe and
workpiece may result.
Blade Installation and Removal (Fig. B)
To Install a Blade
1. Point tool away from body.
2. Use the tab on the blade clamp collar 6 , rotate open the
collar to its full open position.
3. Insert blade 7 fully into blade clamp collar.
nOTE: Blade can be installed with the teeth facing up to
assist in
Flush Cutting
.
4. Release blade clamp collar and gently tug on the blade
to ensure blade is clamped securely.
To Remove a Blade (Fig. B)
WARNING: Burn hazard. Do not touch the the blade
immediately after use. Contact with the blade may
result in personal injury.
1. Rotate open blade clamp collar 6 to its full
open position.
2. Remove blade.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories.
An
accidental start‑up can cause injury.
Wall Mounting
Some PORTER‑CABLE chargers are designed to be wall
mountable or to sit upright on a table or work surface. If wall
mounting, locate the charger within reach of an electrical
outlet, and away from a corner or other obstructions which
may impede air flow. Use the back of the charger as a
template for the location of the mounting screws on the wall.
Mount the charger securely using drywall screws (purchased
separately) at least 1” (25.4 mm) long, with a screw head
diameter of 0.28–0.35” (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32” (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
Charger Cleaning Instructions
WARNING:
Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non‑metallic brush. Do not use water or
any cleaning solutions.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE