Portalp SW10 Скачать руководство пользователя

Страница: 24 / 53

INSTALLATION

GUIDE

SET-UP

PROCEDURES

Perform a setup at the control as follows:

Ensure main power is on

At the I/O control board, depress the SW1 button for approximately 5 seconds. When the red LED (LD2) at the Adjustment Board

begins flashing rapidly, release the button. The blue LED will continue flashing.

Door will slowly go open, recycle partially, close and then re-open.

Do not interrupt the process and do not move the door manually during this time.

If the door does not open and the red LED (DL2) is flashing slowly, check to make sure the motor is plugged in properly at the control

board. Correct as necessary.

Once the setup process is complete, the door will close and the LED will go out.

Setup is complete.

IMPORTANT NOTE:

If the operator stroke is altered in any way, a re-learn must be accomplished.

Upon completion of the Setup, activate the door to open and ensure all performance is acceptable.

Adjust opening and closing speed, as necessary. If speeds are changed, a re-learn is not required.

A re-learn is not required following a main power recovery.

Adjust hold-open time as required.

Additional adjustments are available through the TAP.

– Battery – use CR1216 battery – required to

maintain timer settings and date programmed

by the TAP

TR1

– Opening speed adjustment

TR2

– Closing speed adjustment

TR3

– Hold-open time adjustment

TR4

– Closing speed adjustment when power is

OFF

TR4

will only be enabled when jumper

J6 is moved to the correct pins. (it is enabled

by default).

– USB port

– Ribbon cable connector between boards

– Motor Connector

– Power supply connector between boards

SW1

– “Parameter Changed” button

SW2

– 10 Position “Functions” Dip Switch

For adjustments beyond those mentioned

herein, use the TAP. See TAP Users Guide

for additional information.

WWW.PORTALP.COM

Automatic Doors & Building Access Control

SW10

(Full Power) & S

W19

(Low Energy)

Содержание SW10






















































Результаты поиска

Содержание SW10

Отзывы:

Похожие инструкции для SW10

Бренды по названию

Популярные бренды

Portalp SW10, Руководство по установке

Результаты поиска

Содержание SW10

Отзывы:

Похожие инструкции для SW10

Бренды по названию

Популярные бренды