For an initial functional test of the PSV you proceed as follows:
For an initial functional test of the PSV you proceed as follows:
1.
1. Ins
Insta
tall t
ll the P
he PSV
SV as d
as desc
escrib
ribed i
ed in
n se
se
cti
cti
on
on
3.4
3.4
..
2.
2. Make su
Make sure that th
re that the key swi
e key switch on the c
tch on the contr
ontroller is i
oller is in posit
n position O and t
ion O and the
he
beam shutter on the scanning head is in position OFF.
beam shutter on the scanning head is in position OFF.
3.
3. Posi
Position th
tion the scan
e scanning hea
ning head rough
d roughly suc
ly such that it
h that its lase
s laser beam ape
r beam apertur
rture
e
points to a test surface.
points to a test surface.
4.
4. Swit
Switch the c
ch the contr
ontroller o
oller on by tur
n by turning t
ning the key s
he key swit
witch to po
ch to positi
sition I.
on I.
5.
5. Swit
Switch on the w
ch on the workst
orkstation
ation, sta
, start the PS
rt the PSV sof
V softwar
tware and chang
e and change to the
e to the
Acquisition Mode as described in your
Acquisition Mode as described in your softwa
software manual.
re manual.
6.
6. Befo
Before now open
re now opening the bea
ing the beam shutt
m shutter
er, remem
, remember the inf
ber the informat
ormation on lase
ion on laserr
safety provided in
safety provided in se
se
cti
cti
on
on
1.1
1.1
!!
7.
7. Open t
Open the dus
he dust cov
t cover and th
er and the beam s
e beam shutt
hutter of th
er of the scan
e scanning hea
ning head.
d.
8.
8. T
Test the
est the function
function of the s
of the scanning head
canning head controls (
controls (focus and
focus and position
position of the
of the
laser beam, zoom and focus of the video camera, movement of the pan-tilt
laser beam, zoom and focus of the video camera, movement of the pan-tilt
stage) as described in your software manual.
stage) as described in your software manual.
9.
9. Put a matt wh
Put a matt white test su
ite test surfac
rface, e.g. a piec
e, e.g. a piece of paper
e of paper, at appro
, at approxima
ximately
tely
20
20 cm from the front panel of the scanning head in the
cm from the front panel of the scanning head in the beam path.
beam path.
10.
10. Focus the laser b
Focus the laser beam on the test s
eam on the test surface.
urface.
If the functional test has been successful you can now make measurements
If the functional test has been successful you can now make measurements
as described in
as described in ch
ch
ap
ap
te
te
r
r
4
4
..
If your PSV does not
If your PSV does not perform as described above, read through the
perform as described above, read through the
information on fault diagnosis provided in
information on fault diagnosis provided in ch
ch
ap
ap
te
te
r
r
6
6
and, if necessary, contact
and, if necessary, contact
your local
your local Polytec representative
Polytec representatives.
s.
Содержание PSV 300
