manualshive.com logo in svg

Polymer Laboratories PL-ELS 2100, Руководство по обслуживанию, Страница: 80 / 80

Поделиться
Скачать
Polymer Laboratories PL-ELS 2100 Скачать руководство пользователя страница 80

Version 2.0

76

6_26931B ELS2100_2100 Ice Se rvice Manual_vsn2.0_maste r.doc

CLEANING & DECONTAMINATION PROCEDURES

Switch off and disconnect power cord from instrume nt before 

cleaning or decontamination. Allow any hot parts to cool before 

proceeding.

Cleaning

The exterior of the instrument should be cleaned by wiping down with a soft cloth 

moistened with dilute detergent solution, followed by wiping down with a cloth 

moistened with deionised water. Ensure that no moisture enters the instrument. Allow 

instrument to dry off completely before reconnecting power.

Decontamination

The operator should wear appropriate personal protective equipment for this operation 
(gloves, safety glasses, lab coat and respirator if level of hazard has been risk-assessed 
to be sufficiently high).

Disconnect the instrument completely and remove it to a fume cupboard if necessary. 

Empty the P-trap before moving the instrument. (See “Storing the Instrument”, pg 8). 

Open the cover of the instrument to see if any solvent has contaminated the interior.

Excess quantities of liquid spilt on or inside the instrument should be mopped up 

using absorbent cloths, followed by repeated wiping down with soft cloths moistened 

with Acetone or deionised water (as appropriate to the spilt solvent) until the last 

traces of the hazardous liquid have been removed. If liquid has collected in the drip 

tray around the leak sensor then be very careful not to damage or displace the sensor 

bead whilst mopping up.

Identify and if possible correct source of the leak. Inspect cabling, parts and surfaces 

to determine whether any damage has occurred. If in doubt, contact Polymer 

Laboratories Service Dept for assistance.

Allow the interior and exterior of the instrument to dry out completely before closing 

the cover and reconnecting power.

Dispose of contaminated waste appropriately.

WARNING

!

Содержание PL-ELS 2100

















































































Отзывы:

Нет отзывов