Polarstart PS-4660 TW Скачать руководство пользователя страница 2

Страница: 2 / 31

P. 2

Installation

Guide

PS-4660TW

Table of Contents

Table of Contents .....................................2

Introduction...............................................3

Included in the Kit .....................................3

Installation Points to Remember...............4

Harness Description .................................5

Flashing the Hood-Pin Switch.................12

The Programming Assistance Button .....13

Programming a Transmitter....................14

Before you Proceed................................14

The Transmitter Programming
Procedure ...............................................14

Entering Programming Options Mode ....14

Programming Options.............................16

Multi-Level Features (default state) ........17

Horn Honk Timing...................................19

Tach Programming .................................19

About Tach Programming.......................19

Multi-speed Tach Programming..............20

Automatic Tach Programming ................20

Tach Adjustments...................................21

Testing....................................................21

Closing Up ..............................................22

Supplementary Information.....................23

Fifth Relay Output (2

IGN, ACC or

CRANK)..................................................23

Clutch bypass .........................................23

Ignition-controlled Door Locks ................25

Secure Lock............................................26

Standard Secure Lock ............................26

Smart Secure Lock .................................26

Lock Pulse Duration................................26

Engine Run Time....................................26

Starter Kill (Installation)...........................26

Passive or Active Arming........................27

Resetting the Remote Car Starter ..........27

Events Logging.......................................27

Events playback......................................28

Start Failure Codes through the

Parking Lights.........................................28

Diagnostics – Parking Light Flash
Table.......................................................29

Содержание PS-4660 TW
































Результаты поиска

Содержание PS-4660 TW

Отзывы:

Похожие инструкции для PS-4660 TW

Бренды по названию

Популярные бренды

Polarstart PS-4660 TW, Руководство по установке

Результаты поиска

Содержание PS-4660 TW

Отзывы:

Похожие инструкции для PS-4660 TW

Бренды по названию

Популярные бренды