Available at www.HoneywellStore.com
CEILING FAN AND LIGHT REMOTE
WITH WALL CONTROL
Model 40015 / Item # 0374122
User Guide
IMPORTANT SAFETY INSTRUCTIONS
S
S
1.
Read
and
keep
this
instruction
sheet
for
future
reference.
2.
Please
note
that
all
fixed
wiring
appliances
should
be
installed
by
a
qualified
electrician.
3.
The
supply
to
the
receiver
should
be
connected
on
its
own
circuit.
4.
Switch
off
the
power
at
the
circuit
breaker
before
working
on
receiver
or
ceiling
fan.
5.
This
unit
is
to
be
used
for
the
control
of
a
ceiling
fan
and
its
electrical
source
must
be
AC
110/120V,
60Hz.
6.
Do
not
install
in
damp
location
or
immerse
into
water.
For
indoor
use
only.
7.
Do
not
use
this
remote
with
fans
that
have
pre
‐
installed
remote
controls.
CAUTION: To reduce the risk of fire or injury, do not use this product in
conjunction with any variable (rheostat) wall control.
RECEIVER INSTALLATION INSTRUCTIONS
S
-
NOTE:
This
remote
can
work
with
a
variety
of
hugger
fan
types,
however,
there
is
typically
very
little
space
in
the
hanger
bracket
area
to
install
a
receiver.
Therefore,
we
do
not
recommend
using
this
remote
with
hugger
type
or
5
speed
ceiling
fans.
1.
After
switching
power
off
@
circuit
breaker,
remove
ceiling
fan
canopy
from
the
mounting
bracket.
Disconnect
existing
wiring
between
ceiling
fan
and
supply
at
electrical
junction
box.
2.
Slide
the
receiver
into
the
mounting
bracket
per
FIG.1
being
careful
not
to
pinch
the
antenna
wire.
3.
The
receiver
will
be
inserted
between
the
down
rod
and
the
mounting
bracket.
4.
Make
wiring
connections
per
FIG.
2.
5.
Push
all
connected
wires
back
into
the
junction
box
and
reinstall
the
canopy
onto
the
mounting
bracket.
6.
Manually
set
fan
speed
control
to
HIGH
and
set
light
to
ON
using
the
pull
chains.
NOTE
:
For
the
remote
to
function
properly,
the
fan
must
be
on
HIGH
speed
and
lights
must
be
ON
to
use.
CAUTION: Incorrect wire connection can damage this receiver and could
cause injury or fire.
WALL CONTROL INSTALLATION INSTRUCTIONS
)
1.
Make
the
electrical
connections
to
the
wall
control
(transmitter)
unit
as
shown
in
Fig3.
2.
Carefully
push
all
connected
wires
inside
wall
outlet
box.
3.
Secure
wall
control
unit
with
2
screws
(not
included)
previously
removed
from
the
existing
wall
outlet
box.
4.
After
installed
well,
slide
the
Power
On/Off
switch
on
wall
control
to
“ON”
position.
NOTE:
Before
installing
wall
control,
slide
the
switch
to
“OFF”
position.
ACTIVATING THE LEARNING PROCESS (SMART SYNC)
S
NOTE:
This
remote
is
pre
‐
programmed
from
the
factory
and
should
work
right
out
of
the
box
once
the
battery
is
installed.
Should,
for
any
reason,
re
‐
programming
be
needed
please
follow
the
learning
process
as
follows:
1.
After
installation
is
complete
and
power
is
turned
on,
press
and
hold
the
“FAN
OFF”
button
for
3
seconds.
Fan
will
turn
on
at
high
speed
and
light
(if
installed)
blinks
3
times.
This
confirms
that
the
SMART
SYNC
setting
is
active.
You
now
have
30
seconds
to
press
the
FAN
OFF
key.
Tap
the
FAN
OFF
button
again
to
turn
off
the
fan.
2.
If
user
cannot
finish
the
setting
within
the
30
seconds
time
frame
the
main
power
must
be
turned
off
and
re
‐
started
again.
This
will
reset
the
unit.
Repeat
step
1
until
the
LEARNING
feature
is
activated
as
indicated.
NOTE:
User
must
press
“FAN
OFF”
key
within
30
seconds
after
main
power
is
turned
on.
FAN
CANOPY
MOUNTING
BRACKET
FIG
1
INSERTING RECEIVER
INTO CANOPY ASSEMBLY
WALL CONTROL LIVE (BLACK)
NEUTRAL (WHITE)
ANTENNA
LIGHT
(BLUE)
MOTOR
(BLACK)
MOTOR
(WHITE)
FIG
2
CONNECTING
THE
RECEIVER
TO
THE
FAN
