Polaroid Joshua Captiva Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 134

background image

5 - 5

Functional Test of Joshua Camera

This procedure verifies whether a Joshua Camera is operating normally or not, during each stage of operation.
If you do not obtain the performance results described here, the Camera is not operating properly and should
be adjusted/repaired.

Perform each test in this Check List to substantiate the customer’s complaint or to identify the actual failure
mode occurring.

Note:

The Camera should be in the following state:

•

Camera should be collapsed

•

Film Pack loading door open

•

Film storage compartment empty

•

Trim Switch in normal (middle) position

•

Counter window should be blank

1.

Dark Slide Test

Install Fresh Film Pack

Dark slide cycle occurs.
Flash does not fire.
Counter indexes from 0 to 10.
Dark slide moves to storage chamber.

Erect camera

Short motor jog occurs.
Red LED lights (flash is charging), then goes out.
Green LED lights and stays on (flash is ready).

2.

Exposure Test (Take a Picture)

Press Shutter Button (S1A/S1B)

Flash fires.

Down Fully

Camera cycles, blades open and close, motor runs.
Counter indexes from 10 to 9.
Film frame moves into storage chamber.
Red LED lights (flash is charging), then goes out.
Green LED lights and stays on (flash is ready).
Review Picture Quality.

Move L/D Switch to Dark

Is resulting picture darker?

Arrow and Take a Picture

Counter indexes from 9 to 8.

Move L/D Switch to White

Is resulting picture lighter?

Arrow and Take a Picture

Counter indexes from 8 to 7.

Press Shutter Button Three

Counter indexes to 6, 5 and 4.

More Times

«
...
111
112
113
114
115
...
»

Содержание Joshua Captiva







































































































































Отзывы:

Нет отзывов

Похожие инструкции для Joshua Captiva

Бренд: Dash Страницы: 2

Бренд: Xiaomi Страницы: 11

Бренд: Xiaomi Страницы: 36

Бренд: HIKVISION Страницы: 39

Бренд: Vitek Страницы: 28

Бренд: Sercomm Страницы: 73

Бренд: Hyundai Страницы: 13

Princeton Instruments Nano-XF

Бренд: Teledyne Страницы: 56

Бренд: i3 International Страницы: 11

Бренд: Casio Страницы: 53

Бренд: Ubiquiti Страницы: 56

Бренд: Zee Страницы: 13

Hello Kitty KT7009A

Бренд: Hello Kitty Страницы: 43

Бренд: SiPix Страницы: 35

GXV 3601 N Series

Бренд: Grandstream Networks Страницы: 22

AgfaPhoto WP8000

Бренд: AGFA Страницы: 20

Бренд: Y-cam Страницы: 88

Бренд: Vivitar Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды