Polaroid Joshua Captiva Скачать руководство пользователя страница 63

Страница: 63 / 134

3 - 5

Testing

Ambient Exposure Test

Purpose

The Ambient Exposure Test is used to measure the energy of the film plane during an ambient (visible)
light exposure. The Star Tester light integrating sphere provides a constant scene brightness level of
100 candles/ft

Setup (Figure 3-3)

1. Open the camera door.

2. Using a solder aid tool, manually trip the camera door switch into its down position.

3. Using a solder aid tool, remove the front cover from the camera.

4. Install the Joshua Test Cover in place of the removed front cover.

5. Set the Joshua Test Cover Strobe/Ambient(STB/AMB) switch to its Ambient (AMB) position.

6. Place the camera with the Joshua Test Cover onto the Joshua Horn Assembly.

7. Remove the 640 Nest Assembly from the Star Tester.

Figure 3-3. Ambient Exposure Test Setup

CAMERA

CAMERA DOOR
SWITCH

JOSHUA TEST
COVER

AMBIENT/STROBE
TRIM WHEELS

JOSHUA HORN
ASSEMBLY

Содержание Joshua Captiva







































































































































Результаты поиска

Содержание Joshua Captiva

Отзывы:

Похожие инструкции для Joshua Captiva

Бренды по названию

Популярные бренды

Polaroid Joshua Captiva, Руководство по обслуживанию

Результаты поиска

Содержание Joshua Captiva

Отзывы:

Похожие инструкции для Joshua Captiva

Бренды по названию

Популярные бренды