background image

5

cut correctly if the surface module is
approximately one foot from the pool wall
when the pump is running.

D. Operation

When operating correctly, the surface module 
will float level on the pool surface. It will change
directions approximately every 15-25 seconds.
As the Polaris moves randomly throughout the
pool, it recirculates clean, filtered water.

The filter bag should contact the pool floor a
majority of the time collecting dirt and debris. It
will remove debris as large as leaves or as fine
as sand. The Polaris Turbo Turtle will vacuum and
sweep the pool in three hours or less.

The Polaris comes equipped with an automatic
pressure relief valve in the quick disconnect. If the
Polaris is receiving too much water pressure, it will
release water at the quick disconnect.

Observe the movement of the surface module to
verify that the cleaner is not operating too fast.
The cleaner is operating too fast if the sweep
hose and bag are not in contact with the pool
bottom a majority of the time and the surface
module changes directions more frequently than
every 15 to 25 seconds. In this case, unscrew the
pressure relief valve until the surface module
slows down. For further information, please refer
to the Troubleshooting Section on page 6.

WARNING: IMPROPER OPERATION MAY
RESULT IN DAMAGE TO THE CLEANER, POOL
OR POOL EQUIPMENT.

III. Maintenance

To ensure the Polaris is operating at its optimal
efficiency, it is important to empty the filter bag and
clean the filter screen on a regular basis. It is also

important to maintain a clean pool filter. A dirty
filter can result in sluggish or inefficient operation.
Make sure the Polaris Turbo Turtle is discon-
nected from the pool wall before cleaning and
backwashing the pool filter.

A. Emptying the Filter Bag

1.

Turn off the pool pump. Push in on the
buttons and slide the filter bag off the jet
sweep assembly.

2.

Turn the filter bag inside out over a trash
can. Reattach it making sure the frame of
the filter bag is completely open.

B. Cleaning the Filter Screen

Inside the quick disconnect there is a filter screen.
It acts as a safety filter to keep any debris that is
not caught by your pool filtration system out of the
Polaris. If the filter screen clogs often, consult your
pool professional.

Please Note: Running the Polaris without the filter
screen can damage the Polaris.

To clean the filter screen, pull it out of the quick
disconnect. Rinse out the debris and press the
filter screen firmly back into place.

C. Backwashing the Pool Filter

Always disconnect the Polaris from the pool wall
before cleaning or backwashing the pool filter.
After cleaning or backwashing, let the pool filtra-
tion system run for at least five minutes to flush
out the return lines before reconnecting the
Polaris.

  

  

  

  

Содержание TurboTurtle











Отзывы: