manualshive.com logo in svg

Polaris 2007 Sportsman 450 EFI, Руководство по обслуживанию

Polaris 2007 Sportsman 450 EFI - отличный выбор для любителей активного отдыха. Для того чтобы узнать о техническом обслуживании и ремонте этого ATV, скачайте бесплатно Service Manual с нашего сайта. Подробная инструкция поможет вам правильно обслуживать свой квадроцикл и сохранить его в отличном состоянии.

Поделиться
Скачать
background image

10.44

ELECTRICAL

STARTER SYSTEM 

Troubleshooting

Starter Motor Does Not Run

• Battery discharged.  Low specific gravity

• Loose or faulty battery cables or corroded connections 

(see Voltage Drop Tests)

• Related wiring loose, disconnected, or corroded

• Poor ground connections at battery cable, starter motor 

or starter solenoid (see Voltage Drop Tests)

• Faulty key switch

• Faulty kill switch

• Faulty starter solenoid or starter motor.

• Engine problem - seized or binding (Can engine be 

rotated easily with recoil starter?)

• Starter lockout malfunction

Starter Motor Turns Over Slowly

• Battery discharged - low specific gravity

• Excessive circuit resistance - poor connections (see 

Voltage Drop Test below)

• Engine problem - seized or binding (Can engine be 

rotated easily?)

• Faulty or worn brushes in starter motor

Starter Motor Turns - Engine Does Not Rotate

• Faulty starter drive

• Faulty starter drive gears or starter motor gear

• Faulty flywheel gear or loose flywheel

VOLTAGE DROP TEST

The Voltage Drop Test is used to test for bad connections.  When
performing the test, you are testing the amount of voltage drop
through the connection.  A poor or corroded connection will
appear as a high voltage reading.  Voltage shown on the meter
when testing connections should not exceed .1 VDC per
connection or component.

To perform the test, place the meter on DC volts and place the
meter leads across the connection to be tested.  Refer to the chart
on 1.47 to perform voltage drop tests on the starter system.

Starter Lockout Troubleshooting- EFI 

Models

The starter lockout is controlled by the PDM. Pin 'C' on SSCB
#1 of the PDM senses the transmission signal and determines if
the switch is in Neutral or Park. When the conditions are met, the
PDM will activate SSCB #2 Pin 'N' to ground the starter
solenoid. 

Pin 'G' on SSCB #2 of the PDM senses when the brake is applied
and activates SSCB #2 pin ‘N’ to ground the solenoid. The PDM
will allow starting in Neutral or Park without the brake applied.
Applying the brake overrides this system and allows starting
regardless of transmission shift position.

Items to check when diagnosing a no-start condition are:

• Transmission switch for proper function

• Starter solenoid for proper function

• Brake switch for proper function

• Wire harness, loose connections/pins (including the 

PDM) leading to and from these components

• Proper ground to frame

Should all these items be found in working order, the PDM may
be at fault.

Starter Lockout Troubleshooting- 

Sportsman 450

The starter lockout is controlled by the PDM. Pin 'G' on SSCB
#1 of the PDM senses the transmission signal and determines if
the switch is in Neutral or Park. When the conditions are met, the
PDM will activate Pin 'A' to ground the starter solenoid. 

Pin 'H' on SSCB #1 of the PDM senses when the brake is applied
and activates pin ‘A’ to ground the starter solenoid. The PDM
will allow starting in Neutral or Park without the brake applied.
Applying the brake overrides this system and allows starting
regardless of transmission shift position.

Items to check when diagnosing a no-start condition are:

• Transmission switch for proper function

• Starter solenoid for proper function

• Brake switch for proper function

• Wire harness, loose connections/pins (including the 

PDM) leading to and from these components

• Proper ground to frame

Should all these items be found in working order, the PDM may
be at fault.

Voltage should not exceed

.1 DC volts per connection

Содержание 2007 Sportsman 450 EFI























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2007 Sportsman 450 EFI

Yerf-Dog 3205 Owner'S Manual preview
3205
Бренд: Yerf-Dog Страницы: 21
Yamaha YXZ1000R 2020 Service Manual preview
YXZ1000R 2020
Бренд: Yamaha Страницы: 21
Yamaha 1980 ET340 Manual preview
1980 ET340
Бренд: Yamaha Страницы: 18
Apogee Adapt-X Optimax User Manual preview
Adapt-X Optimax
Бренд: Apogee Страницы: 24
GMX YA49D JUNIOR Assembly Manual preview
YA49D JUNIOR
Бренд: GMX Страницы: 21
GMX Mini e-Quad Assembly Manual preview
Mini e-Quad
Бренд: GMX Страницы: 25
Panasonic HYBRID IP-PBX KX-TDA100 Getting Started preview
HYBRID IP-PBX KX-TDA100
Бренд: Panasonic Страницы: 30
Yamaha DR2A17 EFI PTV Operator'S Manual preview
DR2A17 EFI PTV
Бренд: Yamaha Страницы: 60
Wallenstein LX100 Manual preview
LX100
Бренд: Wallenstein Страницы: 45
Yamaha Raptor YFM350S Ower'S Manual preview
Raptor YFM350S
Бренд: Yamaha Страницы: 173
Malone XtraLight MPG525G Assembly Instructions Manual preview
XtraLight MPG525G
Бренд: Malone Страницы: 25
Yamaha YFM700RV Assembly Manual preview
YFM700RV
Бренд: Yamaha Страницы: 48
Yamaha YFM350FAS Assembly Manual preview
YFM350FAS
Бренд: Yamaha Страницы: 32
Yamaha T-CHIME Assembly Manual preview
T-CHIME
Бренд: Yamaha Страницы: 6
Yamaha WOLVERINE YFM350FXR Owner'S Manual preview
WOLVERINE YFM350FXR
Бренд: Yamaha Страницы: 169
Yamaha SXV60ERJ Owner'S Manual preview
SXV60ERJ
Бренд: Yamaha Страницы: 95
Yamaha SXV60J Owner'S Manual preview
SXV60J
Бренд: Yamaha Страницы: 95
Twister GT200IIR Owner'S Manual - Parts Manual preview
GT200IIR
Бренд: Twister Страницы: 66

Бренды по названию

Популярные бренды

Загрузить еще бренды