Point Grey Flea3 GigE Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 132

background image

Point Grey Flea3 GigE Technical Reference

Contacting Point Grey Research

About This Manual

This manual provides the user with a detailed specification of the Flea3 GigE camera system. The user should be aware
that the camera system is complex and dynamic – if any errors or omissions are found during experimentation, please
contact us. (See

Contacting Point Grey Research

.)

This document is subject to change without notice.

All model-specific information presented in this manual reflects functionality available in the model's
firmware version.

For more information see

Camera Firmware

.

Where to Find Information

Chapter

What You Will Find

Flea3 GigE Specifications

General camera specifications and specific model specifications, and camera properties.

Flea3 GigE Installation

Instructions for installing the Flea3 GigE, as well as introduction to Flea3 GigE configuration.

Tools to Control the Flea3 GigE

Information on the tools available for controlling the Flea3 GigE.

Flea3 GigE Physical Interface

Information on the mechanical properties of the Flea3 GigE.

General Flea3 GigE Operation

Information on powering the Flea3 GigE, monitoring status, user configuration sets, memory
controls, and firmware.

Input/Output Control

Information on input/output modes and controls.

Image Acquisition

Information on asynchronous triggering and supported trigger modes.

Flea3 GigE Attributes

Information on supported imaging parameters and their controls.

Troubleshooting

Information on how to get support, diagnostics for the Flea3 GigE, and common sensor
artifacts.

Appendix:

FlyCapture API Code

Samples

Examples of FlyCapture API code.

Appendix:

FlyCapture SDK

Examples

Sample programs provided with the FlyCapture SDK.

Appendix:

GenICam Features

Information on GenICam Feature controls.

Appendix:

GigE Vision Bootstrap

Registers

Information on GigE Vision Bootstrap Registers.

Appendix:

Control and Status

Registers

Information on IIDC Control and Status Registers for functions not handled via GenICam.

Revised 10/29/2013

Copyright ©2010-2013 Point Grey Research Inc.

ii

«
...
7
8
9
10
11
...
»

Содержание Flea3 GigE





































































































































Отзывы:

Нет отзывов

Похожие инструкции для Flea3 GigE

DSC-350 - Digital Camera - 0.35 Megapixel

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 5

Бренд: D-Link Страницы: 67

Бренд: D-Link Страницы: 8

DSC-350 - Digital Camera - 0.35 Megapixel

Бренд: D-Link Страницы: 2

Бренд: GE Страницы: 84

Бренд: GE Страницы: 86

Бренд: GE Страницы: 86

Бренд: GE Страницы: 86

Бренд: GE Страницы: 76

Бренд: GE Страницы: 76

Бренд: GE Страницы: 76

Бренд: GE Страницы: 76

Бренд: GE Страницы: 79

ACTIVE series G5WP

Бренд: GE Страницы: 87

Бренд: GE Страницы: 2

Бренд: GE Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды