manualshive.com logo in svg

PMD PMDX-132, Руководство пользователя

Поделиться
Скачать
PMD PMDX-132 Скачать руководство пользователя страница 21

PMDX-132 User’s Manual

PCB Revision: PCB-466A

Document Revision: 1.0

Serial Numbers: 23410 and above

PMDX-132_Manual_10.doc

©2008 Practical Micro Design, Inc.

Page 21 of 24

17 April 2008

All Rights Reserved

Setting

Label

Description

1 to 2

normal

Pin 17 from the PC parallel port drives the “pin 17” control output on J9 as well as
the charge pump circuitry.

2 to 3

CP-OK

Pin 17 from the PC parallel port drives only the charge pump circuitry.  The “pin
17” control output on J9 is driven “high” or floats low based on the state of the

E-Stop

, 

Fault

 and 

Motor Disable

 inputs, the Gecko stepper driver “

Error

” signals, and

optionally depending on jumper JP1, the “charge pump” circuit..  See sections 3.5,
and 3.6 for more information.  This setting allows the charge pump circuit to
disable external drivers via opto-isolated relays, or can be used to daisy-chain the
PMDX-132 to a PMDX-122 boards (see section 2.4).

Table 15 – “Pin 17 Mode”  Jumper Settings (JP2)

5.3 

Relay Mode (JP3 and JP4)

These jumpers select whether the PC parallel port signals control the two relays or the relays are not
used.  Figure 10 on page 20 shows the location of these jumpers.

Setting

Label

Description

1 to 2

pin 1

Relay controlled from PC parallel port pin 1 (~Strobe status signal)

2 to 3

disable

Relay is not driven (this silences the relay when J9 pin 1 is used as a digital output)

Table 16 – “K1 Relay Mode”  Jumper Settings (JP3)

Setting

Label

Description

1 to 2

pin 14

Relay controlled from PC parallel port pin 14 (~AutoFeed status signal)

2 to 3

disable

Relay is not driven (this silences the relay when J9 pin 14 is used as a digital output)

Table 17 – “K2 Relay Mode”  Jumper Settings (JP4)

5.4 

Gecko Step  & Direction Common (JP5, JP6, JP7 and JP8)

These jumpers select the common reference voltage for the step and direction signals to each of the four
Gecko modules.  Figure 10 on page 20 shows the location of these jumpers.

Jumper

Gecko

Jumper

Gecko

JP5

Gecko #1

JP7

Gecko #3

JP6

Gecko #2

JP8

Gecko #4

Setting

Label

Description

1 to 2

+5V

+5 volts is the step and direction common reference

2 to 3

GND

Ground is the step and direction common reference

Table 18 – “Gecko Step & Direction Common”  Jumper Settings (JP5, JP6, JP7, JP8)

Содержание PMDX-132

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды