manualshive.com logo in svg

PMD PMDX-132, Руководство пользователя

Поделиться
Скачать
PMD PMDX-132 Скачать руководство пользователя страница 20

PMDX-132 User’s Manual

PCB Revision: PCB-466A

Document Revision: 1.0

Serial Numbers: 23410 and above

PMDX-132_Manual_10.doc

©2008 Practical Micro Design, Inc.

Page 20 of 24

17 April 2008

All Rights Reserved

Figure 10 –Jumper Locations

5.1 

Output Enable (JP1)

This jumper determines when the PMDX-132 outputs are enabled.  This controls all of the outputs: step
and direction (i.e. data bus) and control signals. Figure 10 on page 20 shows the location of this jumper.

Setting

Label

Description

1 to 2

not

Estop

Outputs will be enabled whenever an emergency stop or fault condition does not
exist.  The “charge pump” is ignored.

2 to 3

CP-OK

Outputs will be enable when “charge pump” is in the OK condition 

AND 

no

emergency stop or fault condition exists.

Table 14 – “Output Enable” Jumper Settings (JP1)

5.2 

Pin 17 Mode (JP2)

This jumper selects which signal is presented on the “pin 17” terminal on connector J9.  Figure 10 on page
20 shows the location of this jumper.

Содержание PMDX-132

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды