PMA KS 40, Описание интерфейса

Страница: 7 / 20

KS KS KS
CODE Description 40 50 90 Disp R/W Len. Value range Rem.
51 2nd set-point or
f f f
SP2 R/W 9 SPL ... SPH /- - - -
#>
52
Set-points for programmer
f f f
SP3 R/W 9 SPL ... SPH
53
f f f
SP4 R/W 9 SPL ... SPH
54
Segment times for programmer
f f f
Pt2 R/W 7 0...9999
55
f f f
Pt3 R/W 7 0...9999
56
f f f
Pt4
R/W 7 0...9999
57 5th set-point (programmer)
f f f
SP5 R/W 9 SPL ... SPH
58 5th segment time (progr.)
f f f
Pt5 R/W 7 0...9999
59 Gradient
f f f
Gr R/W 8 0.1...999.9 /- - - -
>
q
61
Configuration level
f f f
Con1 R 7
q
62
f f f
Con2
R 7
q
63 -
f f
Con3 R 7
q
64 - -
f
Con4 R 7
71 Correcting variable for start-up -
f f
YA R/W 6 5...100
72 Set-point for start-up -
f f
SPA R/W 9 SPL ... SPH
73 Holding time for start-up -
f f
PtA
R/W 7 0...9999
74 Max. correct. variable average -
f
- YH R/W 6 5...100
75 Limit for averaging (corr. var.) -
f
- LYH R/W 7 0.1...10.0
76 2nd correcting variable - -
f
Y2 R/W 6 YLL ... YLH
77 Filter time constant - -
f
tF R/W 8 0.0...999.9
78 Span start
f f f
InL R/W 9 –999...( InH - 1)
y
79 Span end
f f f
InH R/W 9 ( InL + 1)...9999
y
81 Decimal point
f f f
dP R/W 4 (dP)
<
82 Lower set-point limit
f f f
SPL R/W 9 InL ...( SPH - 1)
83 Upper set-point limit
f f f
SPH R/W 9 ( SPL + 1)... InH
85 Lower output limit - -
f
YLL R/W 7 -100...( YLH - 10)
86 Upper output limit - -
f
YLH R/W 7 ( YLL + 10)...100
87 Cycle time heating
f f f
t1 R/W 8 0,4...999,9
88 Cycle time cooling
f f f
t2 R/W 8 0,4...999,9
89 Operation locking
f f f
Loc R/W 4 (Loc)
<
B2,01 Set-points SP2 ... SP11 - -
f
R/W 80/83 SPL ... SPH
Ü
B2,02 Segment times Pt2 ... Pt11 - -
f
R/W 60/63 0...9999
Ü
Ü
Block access (
Ä
chapter 3.1, General structure and chapter 6, Communication examples)
*
KS 40 / KS 50: (Y) can be read only.
KS 90:
Y
can be read and written. The written value becomes valid in manual mode.
Ö
The process value is only valid, if bit 3 and bit 5 in status byte 1 are 0 (no sensor or polarity error).
ä Ä
chapter 7, Remote/Local operation
#
With KS 40 / KS 50 positioners: output signal (–100%) / 0%...100%, no switch-off function.
<
The limits of these values depend on the instrument (
Ä
data sheet or operating instructions).
>
If four minus signs are transmitted, the relevant function is switched off.
y
These values can be written only with standard signal input. They must not be changed with running
programmer or ramp (
Ä
NAK).
English CODE table
960612 5 Interface description 9499 040 47701