Platinum Access Systems BARRIER Скачать руководство пользователя

Страница: 34 / 36

Technical Support: (909) 259-6001

BARRIER

Routine Maintenance

Perform the following operations and checks every 6 months according to intensity of use of the automa-

tion. Disconnect the power supply connection and batteries (if present):

•

Clean and oil the levers and check nuts and screws are well tightened.

•

Clean and grease the joint and the spring-post as shown in the figure.

•

Check the electrical connections.

•

Check that the manual release is operating correctly.

•

Check that the rod is balanced correctly.

Check the value of the capacity of the motor condenser.

Reconnect the power supply connection and batteries (if present):

•

Check that the limit switches are working correctly:

•

Check that obstacle detection is operation correctly.

•

Check that all control and safety functions are working correctly.

OBSTRUCTION/INSTANT REVERSING SENSOR

Содержание BARRIER





































Результаты поиска

Содержание BARRIER

Отзывы:

Похожие инструкции для BARRIER

Бренды по названию

Популярные бренды

Platinum Access Systems BARRIER, Руководство по установке

Результаты поиска

Содержание BARRIER

Отзывы:

Похожие инструкции для BARRIER

Бренды по названию

Популярные бренды