Platinum Access Systems BARRIER Скачать руководство пользователя

Страница: 18 / 36

Technical Support: (909) 259-6001

BARRIER

Inductive loop Installation

ALARM RESET SWITCH INSTALLATION:

(UL 325 standard requirement)

is either a Type A or B2 device and the second activation is a Type A device. The alarm shall signal for a minimum

of 5 min or until a renewed manual input from an integral control or a permanently mounted control (such as a Stop

button) located in the line-of-sight of the gate has been entered. An audio alarm is not required for Classes III and IV.

To reset the alarm the Stop command can be given in two different ways.

1- The Built in Stop switch on the control board.

2- The External Stop button in the line-of-sight of the gate, away from moving parts of the gate and out of

reach of children.

STOP

Minimum

Manual Stop

Button

COM

N.C.

STOP

WARNING PLACARDS INSTALLATION:

WARNING – To reduce the risk of severe injury or death to person, please follow these instructions:

All Warning Sings and Placards must be mounted where visible in the area of the gate.

A minimum of two (2) Warning Placards shall be mounted. (One on each side of the gate).

ALARM RESET SWITCH INSTALLATION:

(UL 325 standard requirement)

is either a Type A or B2 device and the second activation is a Type A device. The alarm shall signal for a minimum

of 5 min or until a renewed manual input from an integral control or a permanently mounted control (such as a Stop

button) located in the line-of-sight of the gate has been entered. An audio alarm is not required for Classes III and IV.

To reset the alarm the Stop command can be given in two different ways.

1- The Built in Stop switch on the control board.

2- The External Stop button in the line-of-sight of the gate, away from moving parts of the gate and out of

reach of children.

STOP

Minimum

Manual Stop

Button

COM

N.C.

STOP

WARNING PLACARDS INSTALLATION:

WARNING – To reduce the risk of severe injury or death to person, please follow these instructions:

All Warning Sings and Placards must be mounted where visible in the area of the gate.

A minimum of two (2) Warning Placards shall be mounted. (One on each side of the gate).

BATTERY AND POWER SUPPLY CONNECTION DIAGRAM

Содержание BARRIER





































Результаты поиска

Содержание BARRIER

Отзывы:

Похожие инструкции для BARRIER

Бренды по названию

Популярные бренды

Platinum Access Systems BARRIER, Руководство по установке

Результаты поиска

Содержание BARRIER

Отзывы:

Похожие инструкции для BARRIER

Бренды по названию

Популярные бренды