Platinum Access Systems BARRIER Скачать руководство пользователя

Страница: 16 / 36

Technical Support: (909) 259-6001

BARRIER

LIMIT SWITCH ADJUSTMENTS FOR THE OPENING AND CLOSING POSITION

ELECTRICAL POWER SOURCE CONNECTION (TO CIRCUIT-BOARD)

Electrical Installation

Ground Rod

Earth Ground

- (Green)

Earth Ground (Green/Yellow)

+ (White)

Hot (Black)

Neutral (White)

To Power Harness

power cable to the board. USE MIN. 14 AWG WIRE. FOLLOW ALL LOCAL ELECTRICAL CODES.

Power Harness

White

Green

Red

Black

To help protect the equipment from lightning and power

surges and to protect persons from shock hazard the

Operator must be grounded. The earth ground rod

must be located within 3 feet from the gate operator.

Use the proper type earth ground rod for your local

area. The ground wire must be a single, whole piece of

wire. Never splice two wires for the ground wire. If you

cut the ground wire too short, break it, or destroy

its integrity, replace it with a single wire length.

Prevent unnecessary turns or loops in ground wires.

The gate operator and the battery charger require a

single phase AC line to operate.

1. Turn off the breaker for the circuit you are using.

2. Select the proper voltage on the power board.

3. Connect the incoming power wires to the proper

terminals.

4. Turn on the breaker and check that AC ON and

CHARGE LED are lit.

The power receptacle has been left unconnected till the installer decides what voltage to use.

Connect to 120VAC only

Ground Rod

Earth Ground

- (Green)

Earth Ground (Green/Yellow)

+ (White)

Hot (Black)

Neutral (White)

To Power Harness

power cable to the board. USE MIN. 14 AWG WIRE. FOLLOW ALL LOCAL ELECTRICAL CODES.

Power Harness

White

Green

Red

Black

To help protect the equipment from lightning and power

surges and to protect persons from shock hazard the

Operator must be grounded. The earth ground rod

must be located within 3 feet from the gate operator.

Use the proper type earth ground rod for your local

area. The ground wire must be a single, whole piece of

wire. Never splice two wires for the ground wire. If you

cut the ground wire too short, break it, or destroy

its integrity, replace it with a single wire length.

Prevent unnecessary turns or loops in ground wires.

The gate operator and the battery charger require a

single phase AC line to operate.

1. Turn off the breaker for the circuit you are using.

2. Select the proper voltage on the power board.

3. Connect the incoming power wires to the proper

terminals.

4. Turn on the breaker and check that AC ON and

CHARGE LED are lit.

The power receptacle has been left unconnected till the installer decides what voltage to use.

Connect to 120VAC only

Ground Rod

Earth Ground

- (Green)

Earth Ground (Green/Yellow)

+ (White)

Hot (Black)

Neutral (White)

To Power Harness

power cable to the board. USE MIN. 14 AWG WIRE. FOLLOW ALL LOCAL ELECTRICAL CODES.

Power Harness

White

Green

Red

Black

To help protect the equipment from lightning and power

surges and to protect persons from shock hazard the

Operator must be grounded. The earth ground rod

must be located within 3 feet from the gate operator.

Use the proper type earth ground rod for your local

area. The ground wire must be a single, whole piece of

wire. Never splice two wires for the ground wire. If you

cut the ground wire too short, break it, or destroy

its integrity, replace it with a single wire length.

Prevent unnecessary turns or loops in ground wires.

The gate operator and the battery charger require a

single phase AC line to operate.

1. Turn off the breaker for the circuit you are using.

2. Select the proper voltage on the power board.

3. Connect the incoming power wires to the proper

terminals.

4. Turn on the breaker and check that AC ON and

CHARGE LED are lit.

The power receptacle has been left unconnected till the installer decides what voltage to use.

Connect to 120VAC only

Содержание BARRIER





































Результаты поиска

Содержание BARRIER

Отзывы:

Похожие инструкции для BARRIER

Бренды по названию

Популярные бренды

Platinum Access Systems BARRIER, Руководство по установке

Результаты поиска

Содержание BARRIER

Отзывы:

Похожие инструкции для BARRIER

Бренды по названию

Популярные бренды