Planmeca Compact i3 Скачать руководство пользователя страница 5

Страница: 5 / 106

1 Introduction

This manual contains all the information required to install and set up the

Planmeca Compact i dental unit. Please read this manual carefully before

installing the unit.

NOTE

The information given in this manual should be taken as a general guide for

proper installation of the Planmeca Compact i dental unit. However, in the

cases that this information is contradictory to any local or national building

regulations, the building regulations must always override this manual. In

these cases of contradictory contact your local Planmeca dealer before

proceeding with any changes.

1.1 Contents of packing

The contents of the delivery package are as follows:
•

Junction box

•

Delivery arm and suction arm

•

Patient chair with the upholsteries

•

Tray table, suction tubes, instruments, mounting accessories, suction

cleaning accessories, foot control, adapter cover for the lifting adapter

and Planmeca Compact i dental unit documentation

1.2 Associated documentation

This Planmeca dental unit is delivered with the following manuals and

diagrams:
•

User’s manual
For dental care professionals. Describes the dental unit and its different

parts as well as instructs how to operate and clean the dental unit.

•

Installation manual
For service personnel. Describes how to install the dental unit.

NOTE

Use the installation template (included in delivery) to position the unit

correctly.

•

Technical manual
For service personnel. Gives instructions for service situations.

•

Wiring diagrams (30019022)

•

Pneumatic diagrams (30020918)

Planmeca Romexis software is delivered with the following manuals:
•

Planmeca Romexis user’s manual
For dental care professionals. Describes how to monitor and control the

activities as well as gather data related to dental treatments.

•

Planmeca Romexis quick installation guide
For service personnel. Describes how to install Planmeca Romexis

software.

•

Planmeca Romexis technical manual

1 Introduction

Installation manual

Planmeca Compact i3 1

Содержание Compact i3











































































































Результаты поиска

Содержание Compact i3

Отзывы:

Похожие инструкции для Compact i3

Бренды по названию

Популярные бренды

Planmeca Compact i3, Руководство по установке

Результаты поиска

Содержание Compact i3

Отзывы:

Похожие инструкции для Compact i3

Бренды по названию

Популярные бренды