Planika Galio Fire Pit Black Скачать руководство пользователя страница 8

Страница: 8 / 25

www.planikafires.com

IG0150#05

29.06.2020

Figure 3

3.4.

Installation of the gas linkage

WARNING!!!

The montage and service needs to be conducted by a qualified professional, a company or the gas

supplier.

Before proceeding with the connection of the gas cylinder to the fireplace all activity regarding the correct placement

and installation of the GaLiO Fire Pit Corten needs to be already performed. Place the gas linkage away from hot or

sharp edges and make sure it is not twisted.

3.4.1.

Natural gas connection

First and foremost, make sure that the connecting device is designed to supply a gas suitable for the type placed in

the gas installation. All necessary information regarding the desired parameters of the gas are found on the rating

plate of the device. Before connecting the gas supply, it is necessary to blow them to remove any remaining metal

filings and other contaminants from inside. Automatic gas control system should be protected from moisture and dust.

These factors may cause irreparable damage to the individual components. The pipe supplying gas to the fireplace

should be equipped with a ball valve with a recommended diameter of 1/2 inch. The individual elements of the gas

installation cannot be sealed using Teflon tape or PTFE tape.

The gas valve on the gas pipe must be installed in accordance with applicable national regulations. Before connecting

the gas, make sure that the gas pipes and connections have no dirt. Gas connection is finished with external thread

3/8 ". Regarding gas connection, the following requirements shall apply:

• You must use the gas pipe with the correct dimensions, so there

is no pressure loss.

• Ball gas valve should be installed in an easily accessible place and have the necessary CE mark.

Содержание Galio Fire Pit Black


























Результаты поиска

Содержание Galio Fire Pit Black

Отзывы:

Похожие инструкции для Galio Fire Pit Black

Бренды по названию

Популярные бренды

Planika Galio Fire Pit Black, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Galio Fire Pit Black

Отзывы:

Похожие инструкции для Galio Fire Pit Black

Бренды по названию

Популярные бренды