background image

6

PLANETA

PLANET

PLANET

1861

Heben ohne Grenzen

General safety instructions

We have pointed out already in the introduction how important it is to mind all points 

of this instuction. You should especially be aware of the regulations and laws in 

connection with the product liability and insurance requests.

–   The Operation and maintenance manual has always to be within reach to the place 

of action. It contains important and essential aspects and extracts from the relevant 

standards and precautions. Any non-observance of the guide lines and hints out of 

this manual may lead to injuries or even to death of a user of hoist or other innocent 

persons.

–   In addition to this operation and maintenance manual there are National standards, 

laws and common safety sences to mind and to follow. Have also polution and 

accident prevention regulations in mind! It could also be your obligation to wear 

special protection suits or to use special tools and safety devices for handling of 

dangerous loads.

–   Any working with this hoist and trolley assumes and implies the observance of the 

local accident prevention regulations and the consequently action according these 

regulations.

–   Even then, following up all of this, there could be more danger from untrained or 

not special advised workers using this hoist/trolley not in the sense of its originated 

purpose. Please make sure that only people with education and clear senses will 

use it.

–   Please add to this chapter the instructions given by your company, i.e. regarding 

daily inspections, test procedures, working processes, records, and all instructions 

you think that they are helpfull to prevent accidents.

–   All staff who will work with this lifting equipment must read this booklet prior the 

use of the hoist, especially the chapter about the safety instructions. During the 

operation its too late! This is valid especially for the use of hoists only through 

inspection periods or when doing seldom maintenance work with the hoist.

–   Responsible personal shall check frequently whether the staff working with the hoist 

is doing it according to all safety instructions.

–   The owner of the hoist or of the company and his management are responsible 

for the good condition and for completeness of all necessary safety devices at the 

hoist and that it is used only in a safe manner. The Test booklet must be properly 

held and it has to contain the anual inspection check. We recommend to sign a 

maintenance contract with Planeta-Hebetechnik GmbH who can inspect, maintain 

and repair your equipment periodicly.

–   Please set any chain hoist or trolley out of order if a failure appears in fuction. Call 

for designated help!

Содержание HD3N-EX





























Отзывы: