Planet VC-412 Скачать руководство пользователя страница 7

Страница: 7 / 46

VC-412 User’s Manual

Operating Temperature: 32 to 122

F (0 to 50

Storage Temperature: -13 to 158

F (-25 to 70

Humidity: 10% - 90% Non-Condensing

Certification: FCC, VCCI, CE

Net Weight: 4.16 kg

Dimensions: 446 × 300 × 44 mm

1.3 Package Contents & Hardware Description

Upon opening your package you should have the following items:

•

(1) Power Cord

•

(1) VC-412 Intelligent VDSL Switch

•

(1) RS232 Male Console Cable (DB9 to DB9)

•

(1) Setup and Installation Manual CD

•

(1) Quick Installation Guide

If any of these items are missing, please contact your vendor immediately before

continuing. For additional manuals please contact your vendor.

Before removing the switch from the package please ensure to remove all static devices

and static electricity from your body by touching an available metal plate or grounding

point.

Your new VC-412 has 12 VDSL ports, 12 POTS/ISDN ports, 4 Ethernet ports and 1 Local

Console (RS232) port.

Содержание VC-412















































Результаты поиска

Содержание VC-412

Отзывы:

Бренды по названию

Популярные бренды

Planet VC-412, Руководство пользователя

Результаты поиска

Содержание VC-412

Отзывы:

Бренды по названию

Популярные бренды