manualshive.com logo in svg

Planet VC-412, Руководство пользователя

Поделиться
Скачать
Planet VC-412 Скачать руководство пользователя страница 13

                                                                                                 

VC-412 User’s Manual 

 

9 

. 

Once you have assigned a valid IP address to the Switch, proceed to chapter 4 for an 

explanation of the menu systems and commands. 

 2.3 T

elnet Setup

 

Once you have setup the switch IP address via the Console Port, you are ready to access 

the management functions from any station on your network via Telnet. To connect, 

simply start your telnet client and enter the address you configured into the switch 

(Device IP Address). Below you can see an example of using the standard Windows® 

Telnet client. Before using Telnet, you must first know your Switch device IP address. The 

IP should have been set earlier in the Console setup section. If the IP address has not yet 

been set, refer to the quick installation guide. 

 

For Windows 95/98/NT/2000/XP:   

A.  Press on Start Menu, then on RUN, type in telnet and the device IP address. For 

example, if the IP address is 192.168.0.1, type “

telnet 192.168.0.1

” and hit enter.   

B.  Connection will initiate and you will be prompt to enter password.     

C.  The default password is 

admin

, unless it has been changed previously. 

Once you have logged into the switch, proceed to the next section for an explanation on 

issuing ICD commands.

 

Содержание VC-412















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды