Planet VC-412 Скачать руководство пользователя страница 45

Страница: 45 / 46

VC-412 User’s Manual

can not be saved. Thus, you have to continue the following command to update

the VC-101S firmware.

Refer to the table below for speed versions

Speed VC-101S Version

P R2

(12.5/12.5)

Q R4

(18/16)

A LWD

(4/1)

Now set the remote modem’s speed to A which is the LWD mode.

Command Description: RT <port>-<LWD speed mode>

Command: RT 2-A

Important:

Setting the remote modem’s speed first is very important since connection

will end once the remote modem’s speed differs from the local switch.

Now set the speed of VC-412 back to LWD mode.

Command Description: LT<port>-<LWD speed mode>

Command: LT 2-A

Note:

Connection will re-establish.

Save remote modem’s setting so it will not be lost upon power cycling.

Command Description: SR <port>

Command: SR 2

Adjust the VC-412 back to auto-speed mode.

Command Description: LR <port>-

Command: LR 2-

The figure below illustrates the commands to upgrade a version R4 VC-101S remotely

via VC-412 ICD command.

Содержание VC-412















































Результаты поиска

Содержание VC-412

Отзывы:

Бренды по названию

Популярные бренды

Planet VC-412, Руководство пользователя

Результаты поиска

Содержание VC-412

Отзывы:

Бренды по названию

Популярные бренды