manualshive.com logo in svg

Planet VC-412, Руководство пользователя

Поделиться
Скачать
Planet VC-412 Скачать руководство пользователя страница 10

                                                                                                 

VC-412 User’s Manual 

 

6 

2. 

INSTALLATION

 

2.1 C

onnecting

 VC-412

 

The VC-412 has the ability to provide up to 12 remote VDSL connections. The VC-412 

serves as a VDSL Managerial Switch, it can connect up to 12 sets of PLANET remote 

VDSL modems such as the VC-101S. 

The VC-412 connects to the PBX through the POTS/ISDN ports to provide telephone 

services to the remote ends. The VC-412 VDSL ports then connect to the remote VDSL 

modems via telephone wires with a maximum distance up to 1.5 km. 

The VC-412 takes approximately 15 seconds to start, therefore when connecting the 

VC-412 to a remote modem such as the VC-101S, it will take 15 seconds for link to be 

established. 

VC-412 Ethernet Port-D can serve as an uplink or a regular Ethernet port on, when the 

Uplink button is pressed down it serve as an uplink port, when the Uplink button is 

released it serve as a regular Ethernet port.  Hence when connecting the VC-412 to 

WAN via regular Cat. 5 cable on Port-D press down the Uplink button. 

Содержание VC-412















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды