Planet IPX-600 Скачать руководство пользователя

Страница: 49 / 67

Appendix A

DHCP Server Function Notice

There are two web pages related to the DHCP Server options. One is

DHCP Server Status

in the

DHCP Server

page and the other is the

DHCP Only for IP Phones

in the

User Management

page.

This appendix will illustrate the different combinations and results.

DHCP Server Status

: Enabled / DHCP Only for IP Phones : Checked

The DHCP server in this IPX-600 will only provide IP address to IP Phones with MAC

addresses listed in the user management page, the Notebook/PC in the same network will not

be able to get any IP address from IPX-600. In this way, as depicted in

Figure 1

, the voice

packets from IP Phones will go through IPX-600 and data packets from Notebook/PC will go

through NAT/Router. This is the default setting.

Under this situation, if the APS selection is checked, the IP Phone will also get the

auto-configuration information (file name) from DHCP packets, and the IP Phone could be

installed automatically.

DHCP Server Status

: Disabled

The DHCP Server will not offer IP addresses to any devices that were connected to the LAN

network of the IPX-600.

DHCP Server Status

: Enabled / DHCP Only for IP Phones : Unchecked

The DHCP Server will offer IP addresses to any devices that were connected to the LAN

network of the IPX-600. The devices could be IP Phones and/or Notebook/PC.

Содержание IPX-600




































































Результаты поиска

Содержание IPX-600

Отзывы:

Похожие инструкции для IPX-600

Бренды по названию

Популярные бренды

Planet IPX-600, Руководство пользователя

Результаты поиска

Содержание IPX-600

Отзывы:

Похожие инструкции для IPX-600

Бренды по названию

Популярные бренды