Planet IPX-600 Скачать руководство пользователя

Страница: 18 / 67

Figure 13. DHCP Server page of IPX-600

This DHCP server configuration will work for both

Notebook/PC and IP Phones if the “DHCP only for IP Phones”

box in User Management is disabled. If the “DHCP only for

IP Phones” box in User Management is enabled, this DHCP

server will work only for IP Phones.

Notice

IP PBX

In the following sections, all the IP PBX related functions will be introduced.

System

The System settings are for the IP PBX related basic parameters, including the following parts.

General

Parameter description:

Field

Description

WAN IP

Displayed current WAN IP address of IPX-600

LAN IP

Displayed current LAN IP address of IPX-600

Port

The IPX-600 works as a SIP proxy server for the other SIP devices,

any SIP devices can register to IPX-600 to the WAN IP or LAN IP

addresses, you can change the port of this proxy server by

modifying the

Port

field in the IP PBX Configuration page. The

default value is 5060. The allowed value for this field is between 1

and 65535.

RTP Port Range

This is the range of ports used by the IPX-600 for RTP transmission

and reception. All the calls routed through IPX-600, including call to

auto-attendant, will have the RTP port in this range.

Remote/PBX Codec

IPX-600 will determine the remote call codec by this selection. Also

the IP Phone will use this codec to access the voicemail and IVR.

DTMF

This is the DTMF relay detection method used by IPX-600 when a

Содержание IPX-600




































































Результаты поиска

Содержание IPX-600

Отзывы:

Похожие инструкции для IPX-600

Бренды по названию

Популярные бренды

Planet IPX-600, Руководство пользователя

Результаты поиска

Содержание IPX-600

Отзывы:

Похожие инструкции для IPX-600

Бренды по названию

Популярные бренды