Planet IPX-600 Скачать руководство пользователя страница 11

Страница: 11 / 67

After input username/password, it will get into the configuration main men of IPX-600.

Figure 4. First web page of IPX-600

Please locate your PC in the same network segment

(192.168.0.x) of IPX-600. If you’re not familiar with

TCP/IP, please refer to related chapter on user’s manual

CD or consult your network administrator for proper network

configurations.

Note

LAN/WAN interface quick configurations

Nature of PLANET IPX-600 is an IP Sharing (NAT) device, it comes with two default IP addresses, and

default LAN side IP address is “

192.168.0.1

”, default WAN side IP address is “

172.16.0.1

(port number

is 8080). You may use any PC to connect to the LAN port of IPX-600 to start machine administration.

In general cases, the LAN IP address is the default gateway

Hint

of LAN side workstations for Internet access, and the WAN

IP of IPX-600 are the IP address for remote calling party

to connect with.

Содержание IPX-600




































































Результаты поиска

Содержание IPX-600

Отзывы:

Бренды по названию

Популярные бренды

Planet IPX-600, Руководство пользователя

Результаты поиска

Содержание IPX-600

Отзывы:

Бренды по названию

Популярные бренды