Planar PLANAR-9D-12 Скачать руководство пользователя страница 20

Страница: 20 / 20

PLANAR-8DM

ENG

The warranty does not cover defects appearing as a result of:

force majeure circumstances, including lightning strike, fire, drowning or flood,
unacceptable voltage surges, and road accidents

failure to observe rules of installation, operation, and storage

installation,  repair,  or  maintenance  of  the  heater  performed  by  personnel  or
organizations  not  authorized  by  the  manufacturer  to  perform  installation  and
warranty repair

heater fault due to contamination of the combustion chamber

vehicle electric equipment faults

repair performed by the user or use of inauthentic spare parts.

See www.autoterm.ru for the list of organizations performing

warranty repair of

Advers OOO and Teplostar OOO products.

Please contact Servisnaya kompaniya OOO in Samara (phone

+7(846)207-05-20

) or the

“Forum” section of www.autoterm.ru (in Russian) regarding any issues of technical service.

Содержание PLANAR-9D-12





















Результаты поиска

Содержание PLANAR-9D-12

Отзывы:

Похожие инструкции для PLANAR-9D-12

Бренды по названию

Популярные бренды

Planar PLANAR-9D-12, Руководство по эксплуатации

Результаты поиска

Содержание PLANAR-9D-12

Отзывы:

Похожие инструкции для PLANAR-9D-12

Бренды по названию

Популярные бренды