background image

 

PLANAR-8DM  

ENG 

 

 

 

16 

 

Attention! 

 

1.

 

The fuel line and the fuel pump must be protected from heat and hence should 
not be installed near the exhaust pipe or onto the engine.  

 

2.

 

The fuel line from the fuel pump to the heating element is recommended to be 
installed at a rising angle. 

 

8.5 Installation of heater electric wiring  

Install  heater  wire  harnesses  in  accordance  with  the  heater  electric  circuit  diagram 

shown on  Fig. 4.1. Install  the harnesses  in  a  way  that prevents  their heating, deformation, 
and moving during vehicle operation. Fix the harnesses to vehicle parts with plastic clamps.   

If  needed,  cut  an  unnecessary  part  of  the  harness  out  of  its  middle.  Insulate  the 

connection with two heat shrink sleeves (in scope).  

Attention!

 Good practice is to cut the harness at a 500–700 mm distance  from either 

end  of  the  corrugated  sleeve  of  the  harness  and  cut  out  the  unnecessary  section.  Remove 
wires,  pile  off  insulation  from  the  ends  of  all  wires  to  be  connected,  pull  the  heat  shrink 
sleeve  onto  the  wires  and  twist  wires  of  matching  colors  together.  Install  the  heat  shrink 
sleeve in a way so that the place where the wires are twisted together is in the middle of the 
sleeve.  Heat  the  sleeve  up  and  wait  until  it  shrinks  on  the  wires.  Insert  the  wires  into  the 
corrugated sleeve and cover the connection spot with insulating tape.  

Attention! Remove fuses prior to installation. 

 

  

Fig. 8.9 Position of the terminal block and the socket before installation 

8.6 Control panel installation and connection  

Install the control panel inside the vehicle cabin on the dashboard or in any other place 

suitable for the driver.   

Connect the panel to the heater as shown on the electric circuit diagram (Fig. 4.1).   

 

 

9

 

Check of the heater after installation  

9.1 During installation, ensure:  

-

 

tightness of the fuel lines and clamps  

-

 

secure fastening of heater electric contacts, harnesses, and devices. 

9.2

 

Install 25 А fuses.  

9.3

 

Fill the fuel line with the booster pump (not in scope).  

9.4

 

Switch the heater on and check its operation: 

Terminal block AMR 

282762-1 

Socket АМR 929939-1 

Sealing АМR 828904-1 

Wire 

Содержание PLANAR-9D-12





















Отзывы: