background image

ENG  

PLANAR-8DM 

 

 

 

 

 

19 

 

  

11

 

Possible malfunctions at heater launch and their troubleshooting 

11.1 Faults correctable by the user. If the heater does not start upon turning on, check 

the following: 
1)

 

amount of fuel in the tank and the fuel line after the fuel pump 

2)

 

the 25 А fuse 

3)

 

security of connection of terminal blocks and fuse contacts (oxidation is possible). 

11.2 Any other fault may be identified by the way the panel LED blinks. The number 

of blinks and malfunction codes are specified in Table 6.1. 

11.3  Contact  a  service  station  in  case  any  fault  occurs  during  operation,  apart  from 

those specified in section 11.1. 

12

 

Transportation and storage 

12.1

 

Heaters  are  safe  for  transportation  and  may  be  transported  by  any  means, 

including by air or railroad, provided packed goods are protected from weather according to 
Condition 5  of  GOST  15150-69,  and  from  mechanical  impact  according  to  Category  S  of 
GOST 23216-78. 

12.2  Conditions  of  storage  of  heaters  in  manufacturer’s  packing  must  comply  with 

Condition 2 of GOST 15150-69. 

12.3 Heater shelf life in manufacturer’s packing is 24 months. 

 

 

13

 

Warranty  

13.1 The warranty period expires upon reaching one of the following conditions:  

-

 

18 months have passed after product date of sale 

-

 

the product has been used for more than 1,000 hrs (warranty life) 

-

 

the vehicle the product is installed on has run more than 50,000 km. 

13.2

 

Specified lifetime of the heater is 3,000 hrs.  

13.3

 

In  absence  of  a  stamp  with  a  specified  sale  date,  the  warranty  period  is 

calculated since the date of manufacture.   

13.4

 

The  manufacturer  does  not  accept  claims  on  incomplete  scope  of  supply  and 

mechanical damages after sale.  

13.5

 

The manufacturer guarantees normal operation of its product, provided the user 

observes  all  rules  of  its  operation,  transportation,  and  storage  specified  in  this  manual. 
Should a failure appear during the warranty period, it will be corrected for free. The product 
must  be  installed  by  an  organization  authorized  by  the  manufacturer  and  specified  in  the 
“Installation information” section of the warranty certificate.  

 
 

Содержание PLANAR-9D-12





















Отзывы: