6/12
- Batch number and date of manufacture. Example: CS1-123456 (A19). The last part
of the production batch refers to the month of manufacture (A = January, B = February,
etc.) as well as the year of manufacture (19 = 2019, 20 = 2020, etc.).
9 TECHNICAL DATA
9.1 Housing
Material: Polyamide PA 66, self-extinguishing V0 acc. to UL 94
Protection degree:
IP40 (housing), IP20 (terminal strip)
Cable cross section:
0.2 … 2.5 mm
2
(24 … 12 AWG)
Terminal tightening torque:
0.5 … 0.6 Nm
9.2 General data
SIL (SIL CL):
up to SIL CL 2 acc. to EN 62061
Performance Level (PL):
up to PL d acc. to EN ISO 13849-1
Safety category:
Up to cat. 2 acc. to EN ISO 13849-1
MTTF
D
:
225 years
DC:
high
PFh
D
:
4.18 E-10
Mission time:
20 years
Ambient temperature:
-25°C … +55°C
Storage temperature:
-25°C … +70°C
Mechanical endurance:
> 10 million operating cycles
Electrical endurance:
> 100,000 operating cycles
Pollution degree:
external 3, internal 2
Impulse withstand voltage U
imp
:
4 kV
Rated insulation voltage U
i
:
250 V
Overvoltage category:
II
Air and surface distances:
acc. to EN 60947-1
9.3 Power supply
Rated supply voltage U
n
:
24 Vac/dc; 50…60 hz
Supply voltage tolerance:
±15% of U
n
Max. DC residual ripple in DC:
10%
Power consumption AC:
< 5 VA
Power consumption DC:
< 2 W
9.4 Control circuit
Protection against short circuits:
PTC resistance, Ih = 0.5 A
PTC times:
Response time > 100 ms, release time > 3 s
Maximum resistance per input:
≤
50
Ω
Current per input:
70 mA (typical)
Min. duration of start impulse t
MIN
:
> 100 ms
Response time t
A
:
< 50 ms
Release time
in absence of power supply t
R
:
< 105 ms
Simultaneity time t
C
: unlimited
9.5 Output circuit
Output contacts:
2 NO safety contacts
Contact type:
forcibly guided
Material of the contacts:
gold-plated silver alloy
Maximum switching voltage:
230/240 Vac; 300 Vdc
Max. current per contact:
6 A
Conventional free air thermal current I
th
: 6 A
Max. total current
Σ
I
th
2
:
36 A
2
Minimum current:
10 mA
Contact resistance:
≤
100 m
Ω
External protection fuse:
4 A
Maximum switching load:
1380 VA/W
Utilization categories acc. to EN 60947-5-1:
AC15 (50 … 60 hz)
U
e
= 230 V, I
e
= 3 A
DC13 (6 op. cycles/minute)
U
e
= 24 V, I
e
= 4 A
Utilization category acc. to UL 508:
C300
9.6 Compliance with standards
EN 60204-1, EN ISO 13855, EN ISO 14118, EN ISO 12100, EN ISO 13850,
EN 60529, EN 61000-6-2, EN 61000-6-3, EN 61326-1, EN 60664-1, EN 60947-1,
EN IEC 63000, EN ISO 13849-1, EN ISO 13849-2, EN 62061, UL 508, CSA C22.2 n°
14-95, GB/T14048.5-2017
9.7 Compliance with directives
Machinery Directive 2006/42/EC, EMC Directive 2014/30/EU, RohS Directive
2011/65/EU.
10 SPECIAL VERSIONS ON REQUEST
Special versions of the device are available on request.
These special versions may differ substantially from the indications in these operating
instructions.
The installer must ensure that he has received written information regarding the use
of the special version requested (see paragraph SUPPORT).
11 DISPOSAL
At the end of service life product must be disposed of properly, according to the
rules in force in the country in which the disposal takes place.
12 SUPPORT
The device can be used for safeguarding people’s physical safety, therefore in case of
any doubt concerning installation or operation methods, always contact our technical
support service:
Pizzato Elettrica Srl
Via Torino, 1 - 36063 Marostica (VI) - ITALY
Tel39.0424.470.930
E-mail [email protected]
www.pizzato.com
Our support service provides assistance in Italian and English.
13 EC CONFORMITY DECLARATION
I, the undersigned, as a representative of the following manufacturer:
Pizzato Elettrica Srl - Via Torino, 1 - 36063 Marostica (VI) – ITALY
hereby declare that the product is in conformity with whatever prescribed by the
2006/42/EC Machine Directive. The complete version of the present conformity
declaration is available on our website www.pizzato.com
Marco Pizzato
DISCLAIMER:
Subject to modifications without prior notice and errors excepted. The data given in this sheet
are accurately checked and refer to typical mass production values. The device descriptions and
its applications, the fields of application, the external control details, as well as information on
installation and operation, are provided to the best of our knowledge. This does not in any way mean
that the characteristics described may entail legal liabilities extending beyond the “General Terms of
Sale”, as stated in the Pizzato Elettrica general catalogue. Customers/users are not absolved from
the obligation to read and understand our information and recommendations and pertinent technical
standards, before using the products for their own purposes. Taking into account the great variety of
applications and possible connections of the device, the examples and diagrams given in the present
manual are to be considered as merely descriptive; the user is deemed responsible for checking that
the specific application of the device complies with current standards. This document is a translation
of the original instructions. In case of discrepancy between the present sheet and the original copy,
the Italian version shall prevail. The present manual may not be reproduced, in whole or in part,
without the prior written permission by Pizzato Elettrica.
© 2019 Copyright Pizzato Elettrica. All rights reserved.
