8
ON
R
Troubleshooting
Poor connection of OBD2 connector.
Trouble
Possible Causes
Possible Solutions
The key switch is set to ON but
the display will not light up.
.
Specialized Harness
Poor connection of
Red
Black
If wiring has been direct to power the
and wires may have been improperly
wired or there is a poor connection.
Please reconfirm whether wiring and connections are
correct or not.
The accelerator connector was discon-
nected within 15 minutes after having turned
the key to OFF.
Re-connect the disconnected connector and follow the
directions “How to Turn Off the CHECK Lamp” as bellow to
turn off the lamp.
Follow the instructions in this Manual (
⇒
Page 3) to
connect to Accelerator Connector, and follow the direc-
tions “How to Turn Off the CHECK Lamp” as bellow to turn
off the lamp.
With the key switch in the ON position dis-
connect the accelerator connector or the
connector attached to the unit.
The “Initial Settings” have not been properly
carried out.
A CHECK lamp in vehicle has
gone on.
The “Initial Settings” have not been properly
carried out.
Make the settings by following the directions under
“Initial Settings” found on Page 5 of this Manual.
While making “Initial Settings”
an appears
in the display.
The “Initial Settings” have not been properly
carried out.
Even if the Mode is changed,
the changes cannot be felt.
Set the change ratio under ECO Mode to a smaller value.
The change ratio under ECO Mode is too
great.
The engine seems to stall easily.
While in SPORTS Mode, when
put into reverse (dot
blink) does not appear in the
display.
The unit is connected to the reverse wire of
a navigation system from another company.
The backup lights have been changed to
LED lamps.
Please reconfirm whether wiring and connections are
correct or not.
Follow the instructions for wiring to reverse found in this
Manual (
⇒
Page 4).
●
Replace the backup lights with the car maker’s original
lights.
●
Do not carry out wiring for Reverse Gear.
The wiring to reverse was carried out im-
properly or there is a bad connection.
The key has been turned OFF immediately
after having finished the setting of change
ratios or changing the Mode.
The Mode and/or the setting of
change ratios can not be saved.
After having made settings of change ratios or changing
the Mode, wait for at least 2 seconds before turning the
key OFF.
※
Our products have already been recognized as our Industrial Property or are in the process of receiving Industrial Property status.
※
We plan in the near future to take all possible legal measures to protect against unfair competition from look-alike products using similar
designs, regulating characteristics, circuitry and circuitry layout.
※
We strictly prohibit the unlicensed use of the PIVOT trademark and the unauthorized use of PIVOT User’ s Manual.
How to Turn Off the CHECK Lamp
CHECK Lamp is
ON
①
Under normal conditions, start and stop the engine several times.
②
If that does not turn off the lamp, disconnect the cable from - terminal of the battery for about 10 minutes.
③
If that does not turn off the lamp, please consult your local car dealer and have them turn it off.
Note
If the CHECK Lamp comes on due to some operational mistake, please follow the directions below to turn it off.
F
eatures
Connecting
The Wires
Installing
The Product
Ho
w to
Oper
ate
Bef
o
re
Using
T
roub
le-
Shooting
Initial
Settings
PIVOT CORPORATION
87-3, Shimookada Okada, Matsumoto-shi, Nagano, 390-0313 Japan TEL0263-46-5901
Make the settings by following the directions under
“Initial Settings” found on Page 5 of this Manual,
and follow the directions “How to Turn Off the CHECK
Lamp” as bellow to turn off the lamp.
Make the settings by following the directions under
“Initial Settings” found on Page 5 of this Manual.
