Pitney Bowes DI380 OfficeRight Скачать руководство пользователя страница 69

Страница: 69 / 100

Reference • 4

4-11

SV61656 Rev. A

Message

Action

CLOSE MAN ADV

COVER

The manual advance knob door is not fully

closed. Close door.

DEFLECTOR

ERROR

The half fold function is not possible due to a

fault. Remove fold plates and check for any

material.

DOUBLE FEED

A double feed was detected from the feed

tray indicated. Remove the material from the

machine and restart. If double feeds persist,

request another trial piece.

DOUBLE FEED

CHECK STACKER

A double feed was detected from the feed tray

indicated. Remove the double feed from the

stacker. Restart machine.

FOLD PLATES

NOT SET

The fold plates are not set to the correct posi

tion. Remove fold plates and check for any

material. Install fold plates and restart.

MANUAL FEED

TIMEOUT

Material was not detected as being fed from

the feeder within a set time. In manual feed

mode, you must feed the material within a set

time. Press

Start

to restart the machine.

PAPER SHORT

The inserter detected that the material is too

short in length. Check that actual material

length matches the length displayed. If cor

rect, request another trial piece.

PAPER SHORT

CHECK STACKER

The inserter detected that the material used is

too short in length. Check that actual material

length matches the length displayed. If cor

rect, request another trial piece.

SET LEVER

Manual feed lever in the incorrect position for

the mode you’re running. Move the manual

feed lever to the correct position (left position:

manual; right: automatic).

STREAM FEED

The machine detected two sheets fed to

gether from the feed tray indicated. Remove

material from the machine, reload and restart

machine.

Содержание DI380 OfficeRight





































































































Результаты поиска

Содержание DI380 OfficeRight

Отзывы:

Похожие инструкции для DI380 OfficeRight

Бренды по названию

Популярные бренды

Pitney Bowes DI380 OfficeRight, Руководство оператора

Результаты поиска

Содержание DI380 OfficeRight

Отзывы:

Похожие инструкции для DI380 OfficeRight

Бренды по названию

Популярные бренды