background image

8

EN

ENGLISH

9.  INSTALLING THE LID HANDLE

 

Parts Required:

1  x  Lid Handle 

(#2)

2  x  Lid Handle Bezel 

(#3)

 Installation:

•  Remove the pre-installed screws from the Lid Handle. From inside the 

barrel lid, insert one screw protrude to the outside. Add a Bezel on 

the screw. Then hand-tighten the screw (from the inside) into the Lid 

Handle. Repeat for other side.

10. INSTALLING THE FLAME BROILER COMPONENTS

 

Parts Required:

1  x  Flame Broiler Main Plate 

(#8)

1  x  Flame Broiler Slider 

(#7)

 Installation:

•  Insert the Flame Broiler Main Plate into the main grill. Rest the Flame 

Broiler Main Plate  on  the  built-in  ledge  (on  the  inside  right)  of  the 

Main Grill that directs grease towards the grease bucket spout. Slide 

the entire piece to the left side, and the two slots on the Flame Broiler 

Main Plate will fit into the rounded ledge above the burn pot. It will sit 

slightly at a downward angle. Note illustration 10A.

IMPORTANT:  If  the  Main  Plate  is  resting  on  the  base  of  the  Barrel, 

it is installed incorrectly. Poor installation may result in damage to 

your Main Grill Barrel.

•  Place the Flame Broiler Slider on top of the Flame Broiler Main Plate 

covering the slotted openings. Ensure  the  raised  tab  is on the left 

and the two pins at the bottom of the Flame Broiler Slider place into 

the holes of the Flame Broiler Main Plate to easily adjust for direct and 

indirect flame when cooking. Both  flame  broiler  parts  are  lightly 

coated with oil to avoid rusting when shipped. Note illustration 10B.

NOTE:  To maintain the searing and grilling performance of your cooking 

grids, regular care and maintenance Is required. See Owner's Manual.

11.  INSTALLING FLAME BROILER ADJUSTING BAR

 

Parts Required:

1  x  Flame Broiler Adjusting Bar 

(#5)

1  x  Flame Broiler Adjusting Bar Handle 

(#6)

 Installation:

•  Insert the Flame Broiler Adjusting Bar through the opening hole on 

the left side of the Main Barrel. Add the Flame Broiler Adjusting Bar 

Handle on the end outside the Barrel. Next, slide the notched end of the 

Adjusting Bar into the locking tab on the Flame Broiler Slider, giving you 

adjustable access to the Flame Broiler Slider on the Main Plate.

10B

7

8

10A

8

11

A

C

B

6

5

5

C

B

9

2

3

3

Содержание Navigator 850













Отзывы: