Pioneer HR 1500 PTO Скачать руководство пользователя страница 13

Страница: 13 / 14

www.pioneercoverall.com

866-353-5826

REAR SECTION

- 1 5/8” O.D. x 11 Ga. Steel Tubing.

BOWS

- 1 5/16 O.D. x 11 Ga. Steel Tubing.

ARM MOUNTING BRACKETS

- Steel Weldment

Base Plate - 1/4” H.R.S.
Mounting Hub - 4” O.D. Steel Tube.

SPRING

- Reverse Wound Torsion Spring – 9/16” Diameter Wire.

Spring Wire per ASTM A229 Class I.

HYDRAULICS

FLOW DIVERTER

- 5 GPM constant flow from control port side

COVER CONTROL VALVE

Open Center Configuration

Double Manually operated 4 way valves

Adjustable Pressure Relief Valve

GANTRY LIFT CYLINDER

2” Bore x 1 1/4” Rod x 36” Stroke

Double Acting

Chromed Rod

Welded and Rebuildable

HOSES & FITTINGS

Aeroquip

COVER (TARP)

FABRIC

Heavy Duty Mesh

CONSTRUCTION

Reinforced rear pocket.
Shock cords allow the EXTRA WIDE ( 9’) Tarp to be rolled up onto the roller
assembly.

MISCELLANEOUS

All Brackets etc. are Fabricated Steel Weldments

Содержание HR 1500 PTO















Результаты поиска

Содержание HR 1500 PTO

Отзывы:

Похожие инструкции для HR 1500 PTO

Бренды по названию

Популярные бренды

Pioneer HR 1500 PTO, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание HR 1500 PTO

Отзывы:

Похожие инструкции для HR 1500 PTO

Бренды по названию

Популярные бренды