En
71
13
Additional information
Symptom
Remedy
The receiver suddenly switches off or the
FL OFF
indicator blinks.
There is a problem with the receiver’s power unit or fan. Try turning
on the power. If the same thing happens, the receiver is damaged.
Unplug the receiver from the wall and call a Pioneer authorized
independent service company. (Other symptoms may appear when
the power is turned on.)
OVERHEAT
blinks in the display or
AMP
OVERHEAT
and the
FL OFF
indicator flash
and the power turns off.
Allow the unit to cool down in a well-ventilated place before switch-
ing back on (see
Installing the receiver
on page 6 ).
Wait at least 1 minute, then try turning the power on again.
The temperature within the unit has exceeded the allowablevalue.
Lower the volume level.
The receiver suddenly power off or
ADVANCED MCACC
flashes.
The power unit is damaged. Unplug the receiver from the wall and
call a Pioneer authorized independent service company.
Display blinks
12V TRG ERR
.
An error has arisen in the 12 V trigger jacks. Reconnect accurately
then turn the power back on.
No sound
Symptom
Remedy
No sound is output when an input func-
tion is selected.
No sound is output from the front speak-
ers.
Check the volume, mute setting (press
MUTE
) and speaker setting
(press
SPEAKERS
).
Make sure the correct input function is selected.
Check that the MCACC setup microphone is disconnected.
Make sure the correct input signal is selected (press
SIGNAL SEL
).
Note that when
Fixed PCM
ON
is selected, you won’t be able to
hear any other signal format (see
Setting the Audio options
on
page 47 ).
Check that the source component is connected properly (see
Con-
necting your equipment
on page 11 ).
Check that the speakers are connected properly (see
Connecting
the speakers
on page 13 ).
No sound from the surround or center
speakers.
Check that the Stereo listening mode or the Front Stage Surround
Advance mode isn’t selected; select one of the surround listening
modes (see
Listening in surround sound
on page 36 ).
Check that the surround/center speakers are not set to
NO
(see
Speaker Setting
on page 65 ).
Check the channel level settings (see
Channel Level
on page 66 ).
Check the speaker connections (see
Connecting the speakers
on
page 13 ).
Additional information
Troubleshooting 1
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is
something wrong with this component, check the points below. Sometimes the trouble may lie in
another component. Investigate the other components and electrical appliances being used. If the
trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer
authorized independent service company to carry out repair work.
!
If the unit does not operate normally due to external effects such as static electricity disconnect the
power plug from the outlet and insert again to return to normal operating conditions.
Power
Symptom
Remedy
The power does not turn on.
Make sure that the power cord is plugged in to an active power
outlet.
Try disconnecting from the power outlet, then plugging back in.
Power cannot be turned off. (
ZONE 2 ON
is displayed.)
Press the remote control’s
ZONE 2
, then press
u
RECEIVER
to
switch the Zone 2 off.
The receiver suddenly switches off or the
iPod iPhone iPad
indicator blinks.
Check that there are no loose strands of speaker wire touching
the rear panel or another set of wires. If so, re-attach the speaker
wires, making sure there are no stray strands.
The receiver may have a serious problem. Disconnect from the
power and call a Pioneer authorized independent service com-
pany.
During loud playback the power suddenly
switches off.
Turn down the volume.
Lower the 63 Hz and 125 Hz equalizer levels in the
Manual MCACC
setup
on page 61 .
Switch on the digital safety feature. While holding down
ENTER
on
the front panel, press
u
STANDBY/ON
to set this receiver to the
standby mode. Use
TUNE
i
/
j
to select
D.SAFETY
c
OFF
d
, and
then use
PRESET
k
/
l
to select
1
or
2
(select
D.SAFETY
c
OFF
d
to deactivate this feature). If the power switches off even with
2
switched on, turn down the volume. With
1
or
2
on, some features
may be unavailable.
The unit does not respond when the but-
tons are pressed.
Try switching the receiver off, then back on again.
Try disconnecting the power cord, then connect again.
AMP ERR
blinks in the display, then the
power automatically switches off. The
ADVANCED MCACC
blinks and the power
does not turn on.
The receiver may have a serious problem. Do not try switching the
receiver on. Unplug the receiver from the wall and call a Pioneer
authorized independent service company.
Содержание Elite VSX-50
Страница 1: ...VSX 51 VSX 50 ...
