En
50
09
Using other functions
d Adjustment is not possible unless
V.ADJ
(Advanced Video Adjust) is set to
MEMORY
.
e
!
This setting is only displayed when the video signals below are being input:
—
480i or 576i analog video signals
f
!
This setting is only displayed when the video signals below are being input:
—
480i, 576i, 480p, 576p, 720p, 1080i analog video signals
—
480i, 576i, 480p, 576p, 720p, 1080i, 1080p, 1080p24 HDMI video signals
g This adjustment is only possible when 480i signals are being input from the composite video jacks.
h
!
If the image doesn’t match your monitor type, adjust the aspect ratio on the source component or on the
monitor.
!
This setting is only displayed when 480i/p or 576i/p video signals are being input.
Switching the speaker
terminals
If you selected
Normal(SB/FH)
,
Normal(SB/FW)
or
Speaker B
at
Speaker
system setting
on page 65 , you can switch
between speakers using the
SPEAKERS
button.
If you selected
Front Bi-Amp
or
ZONE 2
, the
button will simply switch your main speaker
terminals on or off.
%
Use SPEAKERS on the front panel to
select a speaker system setting.
As mentioned above, if you have selected
Front Bi-Amp
or
ZONE 2
, the button will simply
switch your main speaker terminal (A) on or off.
Press repeatedly to choose a speaker terminal
option:
When you select
Normal(SB/FH)
, you can select
from:
!
SP:
SB/FH ON
– Surround back or front height
channels are added to the front, center and
surround channels (maximum 5 channels)
and a maximum of 7 channels are output. The
surround back and front height channels are
switched automatically according to the audio
input signal.
!
SP:
SB ON
– Surround back channels are
added to the front, center and surround
channels (maximum 5 channels) and a
maximum of 7 channels are output.
!
SP:
FH ON
– Front height channels are added
to the front, center and surround channels
(maximum 5 channels) and a maximum of 7
channels are output.
!
SP:
OFF
– No sound is output from the
speakers.
When you select
Normal(SB/FW)
, you can select
from:
!
SP:
SB/FW ON
– Surround back or front wide
channels are added to the front, center and
surround channels (maximum 5 channels)
and a maximum of 7 channels are output. The
surround back and front wide channels are
switched automatically according to the audio
input signal.
!
SP:
SB ON
– Surround back channels are
added to the front, center and surround
channels (maximum 5 channels) and a
maximum of 7 channels are output.
!
SP:
FW ON
– Front wide channels are added
to the front, center and surround channels
(maximum 5 channels) and a maximum of 7
channels are output.
!
SP:
OFF
– No sound is output from the
speakers.
When you select
Speaker B
, you can select from:
!
SP:
A ON
– Sound is output from the
A-speaker terminals (up to 7 channels
(including surround back channels),
depending on the source).
!
SP:
B ON
– Sound is output from the two
speakers connected to the B-speaker
terminals. Multichannel sources will not be
heard.
!
SP:
A+B ON
– Sound is output from the
A-speaker terminals (up to 5 channels,
depending on the source), the two speakers
connected to the B-speaker terminals, and
the subwoofer. The sound from the B-speaker
terminals will be the same as the sound
from the A-speaker terminals (multichannel
sources will be downmixed to 2 channels).
!
SP:
OFF
– No sound is output from the
speakers.
Note
!
The subwoofer output depends on the settings
you made in
Manual speaker setup
on page 65
. However, if
SP:
B ON
is selected above, no
sound is heard from the subwoofer (the LFE
channel is not downmixed).
!
All speaker systems (except
Speaker B
connections) are switched off
when headphones are connected.
Using the MULTI-ZONE controls
The following steps use the front panel con-
trols to adjust the sub zone volume and select
sources. See
MULTI-ZONE remote controls
on
page 50 .
1 Press MULTI-ZONE ON/OFF on the
front panel.
Each press selects a MULTI-ZONE option:
!
ZONE 2 ON
– Switches the MULTI-ZONE
feature on
!
MULTI ZONE OFF
– Switches the MULTI-
ZONE feature off
The
MULTI-ZONE
indicator lights when the
MULTI-ZONE control has been switched ON.
2 Press MULTI-ZONE CONTROL on the
front panel.
!
When the receiver is on, make sure that any
operations for the sub zone are done while
ZONE 2 shows in the display. If this is not
showing, the front panel controls affect the
main zone only.
3 Use the INPUT SELECTOR dial to select
the source for the sub zone.
For example,
ZONE 2
CD-R
sends the source
connected to the
CD-R/TAPE
inputs to the sub
room (
ZONE 2
) .
!
If you select
TUNER
, you can use the tuner
controls to select a preset station (see
Saving
station presets
on page 32 if you’re unsure
how to do this). The tuner cannot be tuned to
more than one station at a time. Therefore,
changing the station in one zone also
changes the station in the other zone. Please
be careful not to change stations when
recording a radio broadcast.
4 When Speaker System is set to ZONE 2,
use the MASTER VOLUME dial to adjust
the volume for the sub zone.
5 When you’re finished, press
MULTI-ZONE CONTROL again to return to
the main zone controls.
You can also press
MULTI-ZONE ON/OFF
on
the front panel to switch off all output to the
sub zone.
!
You won’t be able to switch the main zone
off completely unless you’ve switched off the
MULTI-ZONE control first.
!
If you don’t plan to use the MULTI-ZONE
feature for a while, turn off the power in both
the sub and main rooms so that this receiver
is in standby.
MULTI-ZONE remote controls
Press the remote control’s
ZONE 2
to operate
the ZONE 2.
The following table shows the possible MULTI-
ZONE remote controls:
Содержание Elite VSX-50
Страница 1: ...VSX 51 VSX 50 ...
