93
C-AX10
4
5
4
×
2
2
×
2
2
3
6
10
12
11
Note:
Slide the PC Board to rear slide (2 or 3 cm away) after
removing screws, connectors, Heat Sink ASSY and Rear Panel.
And PC Board can lift to upper side when matches a projection
part of the Side Wall with a cut part of the PC Board.
Unhook
Unhook
CRAD ASSY
Remove the Shield Plate B where is in the bottom of
CRAD ASSY. (Three screws)
1
Remove the DIGITAL I/O ASSY, DSP ASSY
and Main Shield.
Heat Sink Assy
Side Wall
Remove a CN101 from the
Power Cord.
Remove all screws.
Power Cord
Remove four connectors.
Note:
Do not remove a screw
of the SG ASSY.
FRAD ASSY
CN405
Front
side
CN406
CN407
CN301
FRAD ASSY
×
3
7
9
8
Caution: Perform styling so that each wire does not come near.
Pass a wire through a slit of
the shield plate every one set
(three sets).
Note:
It becomes an equal interval
wires of each group.
Front side
CN1803
Bind in upper side of CN1803.
Keep distance with wire of
CN1803 and FFC away and
bind it.
DSP ASSY
FFC
CN2109
J2102
Bind
Bind
Bind two pairs of wires
in the player.
DIGITAL
I/O ASSY
Clamp the wires to
connect the DIGITAL
I/O ASSY
Styling in installation (DSP ASSY)
Clamp two wires
(Gray and Black).
Power Cord
G
F
E
Содержание C-AX10
